Nissan Qashqai (2007-2010). Manual — part 602
![](/vehicle/qul/ene/roryboritele/oull.png)
DIFFERENTIAL SIDE OIL SEAL
TM-343
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Note the following, and install in the reverse order of removal.
• Drive each differential side oil seal and side oil seal (transfer joint)
evenly using a commercial service tool so that differential side oil
seal and side oil seal (transfer joint) protrudes by the dimension
(A), (B), or (C) respectively.
Unit: mm (in)
NOTE:
Differential side oil seal and side oil seal (transfer joint) pulling direc-
tion is used as the reference.
CAUTION:
• Never reuse differential side oil seals and side oil seal (transfer joint).
• Apply CVT fluid to differential side oil seals and side oil seal (transfer joint).
Drift to be used:
4WD : Inspection
INFOID:0000000001091252
After completing installation, check for CVT fluid leakage and CVT fluid level. Refer to
.
Dimension A
1.8
±
0.5 (0.071
±
0.020)
Dimension B
2.2
±
0.5 (0.087
±
0.020)
Dimension C
0.5
±
0.5 (0.020
±
0.020)
SCIA6609J
Location
Tool number
Differential side oil seal
Transaxle case side
Commercial service tool [Outer diameter: 54 mm
(2.13 in), inner diameter: 47 mm (1.85 in)]
Converter housing side
Side oil seal (transfer joint)
Transaxle engagement
Commercial service tool [Outer diameter: 70 mm
(2.76 in), inner diameter: 56 mm (2.20 in)]
![](/vehicle/qul/ene/roryboritele/rde.png)
TM-344
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
OIL PUMP FITTING BOLT
OIL PUMP FITTING BOLT
Description
INFOID:0000000000952022
Replace the oil pump fitting bolt and the O-ring if oil leakage or exudes from the oil pump fitting bolt.
Exploded View
INFOID:0000000000952023
Removal and Installation
INFOID:0000000000952024
REMOVAL
1.
Remove Oil pump fitting bolt (1) from transaxle assembly.
2.
Remove O-ring from oil pump fitting bolt.
INSTALLATION
Note the following, and install in the reverse order of removal.
• After completing installation, check for CVT fluid leakage and CVT fluid level. Refer to
.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
1.
Oil pump fitting bolt
2.
O-ring
3.
Transaxle assembly
: Apply CVT Fluid NS-2.
Refer to
for symbols not described on the above.
SCIA7906J
JPDIA0077ZZ
![](/vehicle/qul/ene/roryboritele/ket.png)
AIR BREATHER HOSE
TM-345
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
Exploded View
INFOID:0000000000914718
Removal and Installation
INFOID:0000000000914719
REMOVAL
1.
Remove clip from Air cleaner assembly.
2.
Remove Air breather hose from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Make sure air breather hose not collapsed or blocked due to folding or bending when installed.
• Install air breather hose to air breather tube so that the paint mark
(A) faces upward. Also insert hose to the bend of air breather tube.
1.
Air cleaner assembly
2.
Clip
3.
Air breather hose
4.
Transaxle assembly
JPDIA0080ZZ
SCIA7584J
![](/vehicle/qul/ene/roryboritele/saus.png)
TM-346
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
FLUID COOLER SYSTEM
FLUID COOLER SYSTEM
WATER HOSE
WATER HOSE : Exploded View
INFOID:0000000000967500
WATER HOSE : Removal and Installation
INFOID:0000000000967503
REMOVAL
1.
2.
Remove TCM bracket (1). Refer to
3.
Remove hose clamp, and remove CVT water hose A.
1.
Hose clamp
2.
CVT water hose A
3.
Transaxle assembly
4.
CVT water hose B
A.
Thermostat housing
B.
Heater thermostat
C.
CVT fluid cooler
D.
Water outlet
JPDIA0120ZZ
: Bolt
JPDIA0127ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст