Nissan Qashqai (2007-2010). Manual — part 1897
MWI-6
< FUNCTION DIAGNOSIS >
METER SYSTEM
ARRANGEMENT OF COMBINATION METER
METER SYSTEM : Component Parts Location
INFOID:0000000000892246
JSNIA0321ZZ
A.
M/T models
B.
Diesel engine models
C.
CVT models
JSNIA0314ZZ
MWI
METER SYSTEM
MWI-7
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
METER SYSTEM : Component Description
INFOID:0000000000892247
METER SYSTEM : Operation Description
INFOID:0000000000903726
TRIP COMPUTER
• The display switches in the following order when pressing the trip
switch (1) of the combination meter.
- Trip A
→
Trip B
→
Possible driving distance
→
Average fuel con-
sumption
→
Average vehicle speed
→
Travel time
→
Trip A.
• The items other than “odo meter” and “possible driving distance”
can be reset when pressing and holding the trip switch for 1 sec-
ond or more.
• All items other than “odo meter” and “possible driving distance” can
be reset when pressing and holding the trip switch for 3 seconds or
more.
MAINTENANCE
1.
Turn ignition switch ON from OFF.
1.
Fuel level sensor unit (main)
2.
OAT sensor
3.
Oil pressure switch
4.
Oil level sensor
5.
IPDM E/R
6.
Fuel level sensor unit (sub)
A.
Lower right side of rear seat
B.
Lower left side of rear seat (4WD
models)
Unit
Description
Combination meter
Controls the following with the signals received from each unit via CAN communication and the sig-
nals from switches and sensors.
• Speedometer
• Tachometer
• Warning lamps
• Indicator lamps
• Information display
• Warning chime
IPDM E/R
Reads the ON/OFF signals of the oil pressure switch and transmits the oil pressure switch signal to
the combination meter via BCM with CAN communication line.
Fuel level sensor unit
Oil pressure switch
ECM
Transmits the following signals to the combination meter with CAN communication line.
• Engine speed signal
• Engine coolant temperature signal
• Fuel consumption monitor signal
ABS actuator and electric unit
(control unit)
Transmits the vehicle speed signal to the combination meter with CAN communication line.
BCM
Transmits signals provided by various units to the combination meter with CAN communication line.
Control device
Transmits the following signals to the combination meter.
• Manual mode signal
• Not manual mode signal
• Manual mode shift up signal
• Manual mode shift down signal
TCM
Transmits shift position signal to the combination meter.
Brake fluid level switch
Transmits the brake fluid level switch signal to the combination meter.
Parking brake switch
.
JSNIA0306ZZ
MWI-8
< FUNCTION DIAGNOSIS >
METER SYSTEM
2.
Press and hold the trip switch (1) for 3 seconds or more while
displaying the maintenance information to the information dis-
play (for approximately 5 seconds after the ignition switch is
turned ON).
3.
The maintenance information is flashed and the system enters
in the set/reset mode.
4.
The set/reset can be performed with the following operation dur-
ing flashing.
CLOCK
• The display switches between 12-hour time display mode and 24-
hour time display mode with pressing the
switch (1) of the com-
bination meter.
• The “hour” display of clock is flashed when pressing and holding
the
switch for 3 seconds or more, and then the clock switches to
the time adjustment mode.
METER ILLUMINATION CONTROL
Nighttime Mode
The meter illumination is adjusted to 22 steps by turning the
switch (1). (Daytime mode cannot be adjusted.)
SPEEDOMETER
SPEEDOMETER : System Diagram
INFOID:0000000000892248
SPEEDOMETER : System Description
INFOID:0000000000892249
Trip switch
Pressed
: Reset
Turn right
: Increase the set distance
Turn left
: Decrease the set distance
JSNIA0306ZZ
switch
Pressed
: Changing adjustment “hour” and “minute”
Turn right
: Go
Turn left
: Back
JSNIA0304ZZ
switch
Turn right
: Lightening
Turn left
: Darkening
JSNIA0304ZZ
JSNIA0289GB
MWI
METER SYSTEM
MWI-9
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• The ABS actuator and electric unit (control unit) converts the rectangular wave signal provided by the wheel
sensor to a vehicle speed signal and transmits it to the combination meter via CAN communication.
• The combination meter indicates the vehicle speed to the speedometer according to the vehicle speed sig-
nal received via CAN communication.
SPEEDOMETER : Component Parts Location
INFOID:0000000000897197
SPEEDOMETER : Component Description
INFOID:0000000000892251
TACHOMETER
TACHOMETER : System Diagram
INFOID:0000000000892252
TACHOMETER : System Description
INFOID:0000000000892253
JSNIA0314ZZ
1.
Fuel level sensor unit (main)
2.
OAT sensor
3.
Oil pressure switch
4.
Oil level sensor
5.
IPDM E/R
6.
Fuel level sensor unit (sub)
A.
Lower right side of rear seat
B.
Lower left side of rear seat (4WD
models)
Unit
Description
Combination meter
Indicates the vehicle speed to the speedometer according to the vehicle speed signal received from
ABS actuator and electric unit (control unit) via CAN communication.
ABS actuator and electric unit
(control unit)
Transmits the vehicle speed signal to the combination meter with CAN communication line.
JSNIA0290GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст