KIA Borrego (2017 year). Manual — part 11
Features of your vehicle
•
The sensing distance while backing
Type of warning indicator and sound
up is approximately 120 cm (47 in.)
: with Warning sound
when you are driving less than 10
km/h (6.2 mph).
Warning indicator
Distance
Warning sound
•
The sensing distance while moving
from object
When driving
When driving
forward is approximately 100 cm
forward
rearward
(39 in.) when you are driving less
Buzzer beeps
than 10 km/h (6.2 mph).
100cm~61cm
Front
-
intermittently
•
When more than two objects are
Buzzer beeps
sensed at the same time, the clos-
120cm~61cm
Rear
-
est one will be recognized first.
intermittently
•
The side sensors are activated
Buzzer beeps
Front
when you shift the gear to the R
frequently
(Reverse) position.
60cm~31cm
Buzzer beeps
Rear
-
•
If the vehicle speed is above
frequently
20km/h, the system automatically
Buzzer sounds
turns off. To activate again, push
Front
continuously
the button.
30cm
Buzzer sounds
Rear
-
continuously
✽ NOTICE
It may not operate if it’s distance
✽ NOTICE
from the object is already less than
• The actual warning sound and indicator may differ from the illustration
approximately 25 cm when the sys-
according to objects or sensor status.
tem is ON.
• Do not wash the vehicle's sensor with high pressure water.
4 92
Features of your vehicle
Non-operational conditions of
There is a possibility of parking
CAUTION
parking assist system
assist system malfunction when:
•
This system can only sense
Parking assist system may not
1. Driving on uneven road surfaces
objects within the range and
such as unpaved roads, gravel,
operate normally when:
location of the sensors;
bumps, or gradient.
1. Moisture is frozen to the sensor. (It
It can not detect objects in
2. Objects generating excessive
will operate normally when mois-
other areas where sensors are
noise such as vehicle horns, loud
ture melts.)
not installed. Also, small or
motorcycle engines, or truck air
slim objects, such as poles or
2. Sensor is covered with foreign
brakes can interfere with the sen-
objects located between sen-
matter, such as snow or water, or
sor.
sors may not be detected by
the sensor cover is blocked. (It will
3. Heavy rain or water spray.
the sensors.
operate normally when the materi-
al is removed or the sensor is no
4. Wireless transmitters or mobile
Always visually check behind
longer blocked.)
phones present near the sensor.
the vehicle when backing up.
3. Sensor is stained with foreign mat-
5. Sensor is covered with snow.
• Be sure to inform any drivers
ter such as snow or water.
of the vehicle that may be
(Sensing range will return to nor-
unfamiliar with the system
mal when removed.)
regarding the systems capa-
bilities and limitations.
4.The parking assist button is off.
4 93
Features of your vehicle
Detecting range may decrease
✽ NOTICE
✽ NOTICE
when:
1. The warning may not sound
This system can only sense objects
1. Outside air temperature is
sequentially depending on the speed
within the range and location of the
extremely hot or cold.
and shapes of the objects detected.
sensors, it can not detect objects in
2. Undetectable objects smaller than
2. The parking assist system may
other areas where sensors are not
1 m and narrower than 14 cm in
malfunction if the vehicle bumper
installed. Also, small or slim objects,
diameter.
height or sensor installation has
or objects located between sensors
been modified. Any non-factory
may not be detected.
installed equipment or accessories
Always visually check in front and
The following objects may not be
may also interfere with the sensor
behind the vehicle when driving.
recognized by the sensor:
performance.
Be sure to inform any drivers in the
1. Sharp or slim objects such as
3. Sensor may not recognize objects
vehicle that may be unfamiliar with
ropes, chains or small poles.
less than 30 cm from the sensor,
the system regarding the systems
or it may sense an incorrect dis-
capabilities and limitations.
2. Objects, which tend to absorb sen-
tance. Use with caution.
sor frequency such as clothes,
4. When the sensor is frozen or stained
spongy material or snow.
with snow or water, the sensor may
be inoperative until the stains are
removed using a soft cloth.
5. Do not push, scratch or strike the
sensor with any hard objects that
could damage the surface of the
sensor. Sensor damage could occur.
4 94
Features of your vehicle
Self-diagnosis
WARNING
WARNING
When you shift the gear to the R
Pay close attention when the
(Reverse) position and if one or more
Your new vehicle warranty does
vehicle is driven close to
not cover any accidents or dam-
of the below occurs you may have a
objects on the road, particularly
malfunction in the rear parking assist
age to the vehicle or injuries to
pedestrians, and especially
its occupants related to a park-
system.
children. Be aware that some
ing assist system. Always drive
• You don't hear an audible warning
objects may not be detected by
safely and cautiously.
sound or if the buzzer sounds inter-
the sensors, due to the objects
mittently.
distance, size or material, all of
which can limit the effective-
ness of the sensor. Always per-
•
is displayed. (if equipped)
form a visual inspection to
(blinks)
make sure the vehicle is clear of
If this occurs, we recommend that the
all obstructions before moving
system be checked by an authorized
the vehicle in any direction.
Kia dealer.
4 95
Features of your vehicle
REARVIEW CAMERA (IF EQUIPPED)
WARNING
• This system is a supplemen-
tary function only. It is the
responsibility of the driver to
always check the inside/out-
side rearview mirror and the
area behind the vehicle before
and while backing up because
there is a dead zone that can't
OHM046062L
be seen by the camera.
• Always keep the camera lens
clean. If lens is covered with
foreign matter, the camera
may not operate normally.
❈ If your vehicle is equipped with
AVN(Audio, Video and Navigation)
system, rearview display will show
behind the vehicle through the
OHM046061L
AVN monitor while backing-up.
The rearview camera will activate
Refer to a separately supplied
when the back-up light is ON with the
manual for detailed information.
ignition switch ON and the shift lever
in the R (Reverse) position.
This system is a supplemental sys-
tem that shows behind the vehicle
through the rearview display mirror
while backing-up.
4 96
Features of your vehicle
SURROUND VIEW MONITORING SYSTEM (IF EQUIPPED)
•
When the vehicle speed is over
20km/h, the SVM system is turned
off. If the vehicle speed is not over
20km/h after turning off the SVM
by over speed, the SVM is not
turned on. To operate again, push
the button.
•
When the vehicle moves back-
wards, regardless of On/Off of but-
ton and vehicle speed, the SVM is
operated.
OHM046543
•
When the trunk and driver/passen-
This is the parking support system to
ger door are opened and the out-
show around circumstance when you
side mirror is folded, the warning is
park the vehicle in monitor. When
illuminated in SVM system.
you push the button in [ON] position,
•
If the SVM system is not normally
it is operated. To cancel the system,
operated, we recommend that you
push again.
contact an authorized Kia dealer.
Operating conditions
* SVM : Surround View Monitoring
- When ignition is ON
- When the transaxle is on D, N or R
- When the vehicle speed is not over
20km/h
4 97
Features of your vehicle
LIGHTING
Battery saver function
Daytime running light
CAUTION
(if equipped)
•
The purpose of this feature is to
If the driver gets out of the vehi-
prevent the battery from being dis-
The Daytime Running Lights (DRL)
cle through other doors (except
charged. The system automatically
can make it easier for others to see the
driver's door), the battery saver
turns off the parking lights when
front of your vehicle during the day.
function does not operate.
the driver removes the ignition key
DRL can be helpful in many different
Therefore, It causes the battery
and opens the driver-side door.
driving conditions, and it is especially
to be discharged. In this case,
helpful after dawn and before sunset.
•
With this feature, the parking lights
make sure to turn off the lamp
will turn off automatically if the driver
The DRL system will turn the dedi-
before getting out of the vehicle.
parks on the side of the road at night.
cated lamp OFF when:
If necessary, to keep the lights on
1. The headlight or fog lamp switch is
when the ignition key is removed,
ON.
perform the following:
2. The engine is OFF.
1) Open the driver-side door.
2) Turn the parking lights OFF and
ON again using the light switch
on the steering column.
4 98
Features of your vehicle
❈ Traffic Change (For Europe)
Lighting control
Parking light position (
)
The low beam light distribution is
asymmetric. If you go abroad to a
country with opposite traffic direc-
tion, this asymmetric part will dazzle
oncoming car driver. To prevent daz-
zle, ECE regulation demand several
technical solutions
(ex. automatic
change system, adhesive sheet,
down aiming). This headlamps are
designed to adjust in user setting
mode in cluster.
OHM048064L
OHM046065
The light switch has a Headlight and
When the light switch is in the park-
a Parking light position.
ing light position
(2nd position), the
tail, license and instrument panel
To operate the lights, turn the knob at
lights will turn ON.
the end of the control lever to one of
the following positions:
(1) OFF Position
(2) Parking light position
(3) Headlight position
(4) Auto light position
4 99
Features of your vehicle
Headlight position (
)
Auto light position
CAUTION
•
Never place anything over the
sensor
(1) located on the
instrument panel. This will
ensure better auto-light sys-
tem control.
•
Don’t clean the sensor using a
window cleaner. The cleaner
may leave a light film which
could interfere with sensor
operation.
•
If your vehicle has window tint
OHM046066
OHM048067L
or other types of metallic coat-
When the light switch is in the head-
When the light switch is in the AUTO
ing on the front windshield,
light position (3rd position), the head,
light position, the taillights and head-
the Auto light system may not
tail, license and instrument panel
lights will be turned ON or OFF auto-
work properly.
lights will turn ON.
matically depending on the amount
of light outside the vehicle.
✽ NOTICE
The ignition switch must be in the
ON position to turn on the head-
lights.
4 100
Features of your vehicle
High beam operation
WARNING
Do not use high beam when
there are other vehicles. Using
high beam could obstruct the
other driver’s vision.
OHM046068
To flash the headlights, pull the lever
OHM046069
towards you. It will return to the nor-
To turn on the high beam headlamp,
mal
(low beam) position when
push the lever away from you. The
released. The headlight switch does
lever will return to its original position.
not need to be on to use this flashing
The high beam indicator will light
feature.
when the headlight high beams are
switched on.
To prevent the battery from being
discharged, do not leave the lights
on for a prolonged time while the
engine is not running.
4 101
Features of your vehicle
High Beam Assist (if equipped)
Operating condition
The high beam switches to low beam
in the below conditions.
1.Place the light switch in the AUTO
position.
-
When the High Beam Assist is off.
2.Turn on the high beam by pushing
-
When the light switch is not in the
the lever away from you.
AUTO position.
The High Beam Assist (
) indica-
-
When the headlamp is detected
tor will illuminate.
from the on-coming vehicle.
3.The High Beam Assist will turn on
-
When the tail lamp is detected
when vehicle speed is above
from the front vehicle.
45kph (28mph).
-
When the surrounding is bright
• If the lever is pushed away when
enough high beams are not need-
the High Beam Assist is operat-
ed.
OHM046565
ing, the High Beam Assist will
-
When streetlights or other lights
The High Beam Assist is a system
turn off and the high beam will be
are detected.
that automatically adjusts the head-
on continuously. The High Beam
-
When vehicle speed is below
lamp range (switches between high
Assist (
) indicator will turn off.
35km/h (22 mph).
beam and low beam) according to
• If the lever is pulled towards you
-
When headlamp / taillamp of bicy-
the brightness of other vehicles and
when the High Beam Assist is
cle/motorcycle is detected.
road conditions.
operating, the High Beam Assist
will turn off.
4.If the light switch is placed to the
headlamp position, the High Beam
Assist will turn off and the low
beam will be on continuously.
4 102
Features of your vehicle
(Continued)
CAUTION
WARNING
•
When headlamp aiming is not
The system may not operate nor-
•
Do not place any accessories,
properly adjusted.
mally in the below conditions.
stickers or tint the windshield.
•
When driving on a narrow
•
When the light from the on-com-
•
Have the windshield glass
curved road or rough road.
ing or front vehicle is not detect-
replaced from an authorized
ed because of lamp damage,
•
When driving downhill or uphill.
dealer.
hidden from sight, etc.
•
When only part of the vehicle in
•
Do not remove or impact relat-
•
When the lamp of the on-com-
front is visible on a crossroad or
ed parts of the High Beam
ing or front vehicle is covered
curved road.
Assist system.
with dust, snow or water.
•
When there is a traffic light,
•
Be careful that water doesn’t
•
When the light from the on-com-
reflecting sign, flashing sign or
get into the High Beam Assist
ing or front vehicle is not detect-
mirror.
unit.
ed because of exhaust fume,
•
When the road conditions are
•
Do not place objects on the
smoke, fog, snow, etc.
bad such as being wet or cov-
dashboard that reflects light
•
When the front window is cov-
ered with snow.
such as mirrors, white paper,
ered with foreign matters such
•
When the front vehicle’s head-
etc. The system may malfunc-
as ice, dust, fog, or is damaged.
lamps are off but the fog lamps
tion if sunlight is reflected.
•
When there is a similar shape
on.
•
At times, the Smart High
lamp with the front vehicle’s
•
When a vehicle suddenly
Beam system may not work
lamps.
appears from a curve.
properly, always check the
•
When it is hard to see because
road conditions for your safe-
•
When the vehicle is tilted from a
of fog, heavy rain or snow.
ty. When the system does not
flat tire or being towed.
operate normally, manually
•
When the headlamp is not
•
When the LDWS (lane departure
change between the high
repaired or replaced at an
warning system) warning light
beam and low beam.
authorized dealer.
illuminates. (if equipped)
(Continued)
4 103
Features of your vehicle
Turn signals and lane change
To signal a lane change, move the
One-touch lane change function
signals
turn signal lever slightly and hold it in
(if equipped)
position (B). The lever will return to
To activate an one-touch lane
the OFF position when released.
change function, move the turn sig-
If an indicator stays on and does not
nal lever slightly for less than
0.5
flash or if it flashes abnormally, one of
second and then release it. The lane
the turn signal bulbs may be burned
change signals will blink 3 times.
out and will require replacement.
✽ NOTICE
If an indicator flash is abnormally
quick or slow, a bulb may be burned
out or have a poor electrical connec-
tion in the circuit.
OHM046070
The ignition switch must be on for the
turn signals to function. To turn on
the turn signals, move the lever up or
down (A). The green arrow indicators
on the instrument panel indicate
which turn signal is operating. They
will self-cancel after a turn is com-
pleted. If the indicator continues to
flash after a turn, manually return the
lever to the OFF position.
4 104
Features of your vehicle
Front fog light
Rear fog light (if equipped)
✽ NOTICE
To turn on the rear fog light switch,
the ignition switch must be in the ON
position.
OHM046071
OHM046314L
Fog lights are used to provide
To turn the rear fog lights on, turn the
improved visibility when visibility is
headlight switch to the headlight on
poor due to fog, rain or snow, etc.
position and press the rear fog light
The fog lights will turn on when the
switch (light on switch will illuminate).
fog light switch (1) is turned on after
The rear fog lights turn on when the
the parklight is turned on.
rear fog switch is pressed after the
To turn off the fog lights, turn the fog
front fog switch is turned to the ON
light switch (1) to the OFF position.
position and the headlight switch to
the parklight position. (if equipped)
To turn the rear fog lights off, press
CAUTION
the rear fog light switch again or turn
When in operation, the fog
the headlight switch to the OFF posi-
lights consume large amounts
tion.
of vehicle electrical power. Only
use the fog lights when visibility
is poor.
4 105
Features of your vehicle
Headlight leveling device
Listed below are the examples of
Automatic type
(if equipped)
proper switch settings. For loading
It automatically adjusts the headlight
conditions other than those listed
Manual type
beam level according to the number
below, adjust the switch position so
of passengers and loading weight in
that the beam level may be the near-
the luggage area.
est as the condition obtained accord-
And it offers proper headlight beam
ing to the list.
under various conditions.
Switch
Loading condition
position
WARNING
If it does not work properly even
Driver only
0
though your car is inclined
backward according to passen-
Driver + Front passenger
0
ger's posture, or the headlight
beam is irradiated to the high or
Driver + Front passenger+
OHM048223N
1
low position, we recommend
3rd row passenger
To adjust the headlight beam level
that the system be inspected by
according to the number of passen-
Full passengers
1
an authorized Kia dealer.
(Including driver)
gers and loading weight in the luggage
Do not attempt to inspect or
area, turn the beam leveling switch.
Full passengers (including driv-
replace the wiring yourself.
The higher the number of the switch
er) + Maximum permissible load-
2
position, the lower the headlight
ing
beam level. Always keep the head-
Driver + Maximum permissible
3
light beam at the proper leveling
loading
position, or headlights may dazzle
other road users.
4 106
Features of your vehicle
WIPERS AND WASHERS
■ Type A
Front windshield wiper and
Windshield wipers
washer
Operates as follows when the igni-
A : Wiper speed control
tion switch is turned ON.
·
(MIST) - Single wipe
MIST/
: For a single wiping cycle,
INT /
move the lever to this
· OFF (0) - Off
AUTO*
(MIST/
) position and
· INT (---) - Intermittent wipe
release it. The wipers will
AUTO* - Auto control wipe
operate continuously if the
· LO (1) - Low wiper speed
lever is held in this posi-
OTQ049902L
tion.
· HI (2) - High wiper speed
■ Type B
OFF / O : Wiper is not in operation
INT / --- : Wiper operates intermit-
B : Intermittent wipe time adjust-
tently at the same wiping
ment
intervals. Use this mode in
--- /
light rain or mist. To vary
AUTO*
C : Wash with brief wipes*
the speed setting, turn the
speed control knob.
* if equipped
LO / 1 : Normal wiper speed
HI / 2 : Fast wiper speed
OTQ049902
4 107
Features of your vehicle
✽ NOTICE
Auto control (if equipped)
To vary the speed setting, turn the
speed control knob (1).
If there is heavy accumulation of
snow or ice on the windshield,
If the wiper switch is set in AUTO
defrost the windshield for about 10
mode when the ignition switch is ON,
minutes, or until the snow and/or ice
the wiper will operate once to per-
is removed before using the wind-
form a self-check of the system. Set
shield wipers to ensure proper oper-
the wiper to OFF (O) position when
ation. If you do not remove the snow
the wiper is not in use.
and/or ice before using the wiper
Rain sensor
and wash-er, it may damage the
CAUTION
Wiper and washer system.
When the ignition switch is ON
and the windshield wiper switch
OHM046202L
is placed in the AUTO mode, use
The rain sensor located on the upper
caution in the following situa-
end of the windshield glass senses
tions to avoid any injury to the
the amount of rainfall and controls
hands or other parts of the body:
the wiping cycle for the proper inter-
• Do not touch the upper end of
val. The more it rains, the faster the
the windshield glass facing
wiper operates. When the rain stops,
the rain sensor.
the wiper stops.
• Do not wipe the upper end of
the windshield glass with a
damp or wet cloth.
• Do not put pressure on the
windshield glass.
4 108
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст