Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 225
EN(H4DOTC)(diag)-124
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
ENGINE (DIAGNOSTICS)
Q: DTC P0103 MASS OR VOLUME AIR FLOW CIRCUIT HIGH INPUT
DTC DETECTING CONDITION:
• Immediately at fault recognition
• GENERAL DESCRIPTION <Ref. to GD(H4DOTC)-38, DTC P0103 MASS OR VOLUME AIR FLOW CIR-
CUIT HIGH INPUT, Diagnostic Trouble Code (DTC) Detecting Criteria.>
TROUBLE SYMPTOM:
• Improper idling
• Engine stalls.
• Poor driving performance
CAUTION:
After servicing or replacing faulty parts, perform Clear Memory Mode <Ref. to EN(H4DOTC)(diag)-63,
OPERATION, Clear Memory Mode.>, and Inspection Mode <Ref. to EN(H4DOTC)(diag)-49, PROCE-
WIRING DIAGRAM:
• Engine electrical system, without SI-DRIVE <Ref. to WI-32, WITHOUT SI-DRIVE, WIRING DIAGRAM,
• Engine electrical system, with SI-DRIVE <Ref. to WI-48, WITH SI-DRIVE, WIRING DIAGRAM, Engine
ECM
EN-08725
B135
B:
B3
B83
3
B3
B135
B:
B136
C:
1 2 3 4 5
*
*
4
1
5
2
C11
C31
C22
B30
C10
*
B220
24
23
22
21
15A
B220
3
4
B136
C:
B83
6
4 5
3
2
1
35
27
16
10 11 12 13 14 15
25
24
30
9
8
7
17 18 19 20
28
21 22 23
29
32
31
1
2
3
4
5
6
26
33 34
B220
18
19
6
7
4
3
5
2
1
12
11
10
9
8
40
36 39
38
37
34
33
35
32
28 31
30
29
23
22
21
20
26
25
24
27
17
16
15
14
13
35
34
33
32
31
30
29
21
20
19
18
17
16
28
27
26
15
14
13
12
11
25
23
22
24
10
3
4
9
1
2
8
7
6
5
SBF-7
E
FUSE
(RELAY BLOCK)
MAIN RELAY
: TERMINAL No. OPTIONAL
ARRANGEMENT
MASS AIR FLOW &
INTAKE AIR
TEMPERATURE SENSOR
BATTERY
EN(H4DOTC)(diag)-125
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
ENGINE (DIAGNOSTICS)
Step
Check
Yes
No
1
CHECK CURRENT DATA.
1) Start the engine.
2) Read the value of «Air Flow Sensor Volt-
age» using Subaru Select Monitor.
NOTE:
Is the value of «Air Flow Sensor
Voltage» 5 V or more?
Even if DTC is
detected, the cir-
cuit has returned to
a normal condition
at this time. Repro-
duce the failure,
and then perform
the diagnosis
again.
NOTE:
In this case, tem-
porary poor con-
tact of connector,
temporary open or
short circuit of har-
ness may be the
cause.
2
CHECK HARNESS BETWEEN ECM AND
MASS AIR FLOW AND INTAKE AIR TEM-
PERATURE SENSOR CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from the mass
air flow and intake air temperature sensor.
3) Start the engine.
4) Read the value of «Air Flow Sensor Volt-
age» using Subaru Select Monitor.
NOTE:
Is the value of «Air Flow Sensor
Voltage» 5 V or more?
Repair the short
circuit of harness
to power supply
between ECM con-
nector and the
mass air flow and
intake air tempera-
ture sensor con-
nector.
3
CHECK HARNESS BETWEEN ECM AND
MASS AIR FLOW AND INTAKE AIR TEM-
PERATURE SENSOR CONNECTOR.
1) Turn the ignition switch to OFF.
2) Measure the resistance of harness between
mass air flow and intake air temperature sensor
connector and engine ground.
Connector & terminal
(B3) No. 4 — Engine ground:
Is the resistance less than 5 Ω? Go to step
Repair the harness
and connector.
NOTE:
In this case, repair
the following item:
• Open circuit in
harness between
ECM
connector
and the mass air
flow and intake air
temperature sen-
sor connector
• Poor contact of
ECM connector
4
CHECK FOR POOR CONTACT.
Check for poor contact of mass air flow and
intake air temperature sensor connector.
Is there poor contact of mass
air flow and intake air tempera-
ture sensor connector?
Repair the poor
contact of mass air
flow and intake air
temperature sen-
sor connector.
EN(H4DOTC)(diag)-126
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
ENGINE (DIAGNOSTICS)
R: DTC P0107 MANIFOLD ABSOLUTE PRESSURE/BAROMETRIC PRESSURE
CIRCUIT LOW INPUT
DTC DETECTING CONDITION:
• Immediately at fault recognition
• GENERAL DESCRIPTION <Ref. to GD(H4DOTC)-40, DTC P0107 MANIFOLD ABSOLUTE PRESSURE/
BAROMETRIC PRESSURE CIRCUIT LOW INPUT, Diagnostic Trouble Code (DTC) Detecting Criteria.>
CAUTION:
After servicing or replacing faulty parts, perform Clear Memory Mode <Ref. to EN(H4DOTC)(diag)-63,
OPERATION, Clear Memory Mode.>, and Inspection Mode <Ref. to EN(H4DOTC)(diag)-49, PROCE-
WIRING DIAGRAM:
• Engine electrical system, without SI-DRIVE <Ref. to WI-32, WITHOUT SI-DRIVE, WIRING DIAGRAM,
• Engine electrical system, with SI-DRIVE <Ref. to WI-48, WITH SI-DRIVE, WIRING DIAGRAM, Engine
ECM
EN-08724
6
2
8
23
1
3
2
1 2 3 4
12 13 14 15
5 6 7 8
16 17 18 19
9 10 11
20 21 22
23 24 25 26 27 28 29 30 31 32 33
35
34
37
36
39
38
41
40
43
42
44 45
47
46
49
48
51
50
53
52
54
B134
A:
A29
D20
A19
2
3
1
B137
D:
31
30
29
28
27
21
20
19
18
17
16
26
25
24
15
14
13
12
11
23
22
10
3
4
9
1
2
8
7
6
5
3
2
1
B137
D:
B134
A:
B21
E21
E21
E2
B21
31
30
32
29
34
33
21
20
19
18
17
16
28
27
26
15
14
13
12
11
25
23
22
24
10
3
4
9
1
2
8
7
6
5
ES
SI
SI
ES
: WITHOUT SI-DRIVE
: WITH SI-DRIVE
MANIFOLD
ABSOLUTE
PRESSURE
SENSOR
EN(H4DOTC)(diag)-127
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
ENGINE (DIAGNOSTICS)
Step
Check
Yes
No
1
CHECK CURRENT DATA.
1) Start the engine.
2) Read the value of «Mani. Absolute Pres-
sure» using the Subaru Select Monitor or a gen-
eral scan tool.
NOTE:
• Subaru Select Monitor
For detailed operation procedures, refer to
“READ CURRENT DATA FOR ENGINE”. <Ref.
to EN(H4DOTC)(diag)-40, Subaru Select Moni-
tor.>
• General scan tool
For detailed operation procedures, refer to the
general scan tool operation manual.
Is the value of «Mani. Absolute
Pressure» less than 13.3 kPa
(100 mmHg, 3.94 inHg)?
Even if DTC is
detected, the cir-
cuit has returned to
a normal condition
at this time. Repro-
duce the failure,
and then perform
the diagnosis
again.
NOTE:
In this case, tem-
porary poor con-
tact of connector,
temporary open or
short circuit of har-
ness may be the
cause.
2
CHECK POWER SUPPLY OF MANIFOLD
ABSOLUTE PRESSURE SENSOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from manifold
absolute pressure sensor.
3) Turn the ignition switch to ON.
4) Measure the voltage between manifold
absolute pressure sensor connector and
engine ground.
Connector & terminal
(E21) No. 3 (+) — Engine ground (–):
Is the voltage 4.5 V or more?
Repair the harness
and connector.
NOTE:
In this case, repair
the following item:
• Open circuit of
harness between
ECM
connector
and manifold abso-
lute pressure sen-
sor connector
• Poor contact of
ECM connector
• Poor contact of
coupling connector
3
CHECK HARNESS BETWEEN ECM AND
MANIFOLD ABSOLUTE PRESSURE SEN-
SOR CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Measure the resistance of harness between
ECM connector and manifold absolute pres-
sure sensor connector.
Connector & terminal
Models without SI-DRIVE
(B137) No. 20 — (E21) No. 2:
Models with SI-DRIVE
(B137) No. 20 — (E21) No. 1:
Is the resistance less than 1 Ω? Go to step
Repair the harness
and connector.
NOTE:
In this case, repair
the following item:
• Open circuit of
harness between
ECM
connector
and manifold abso-
lute pressure sen-
sor connector
• Poor contact of
coupling connector
4
CHECK HARNESS BETWEEN ECM AND
MANIFOLD ABSOLUTE PRESSURE SEN-
SOR CONNECTOR.
Measure the resistance between ECM connec-
tor and chassis ground.
Connector & terminal
(B137) No. 20 — Chassis ground:
Is the resistance 1 MΩ or
more?
Repair short circuit
to ground in har-
ness between
ECM connector
and manifold abso-
lute pressure sen-
sor connector.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст