Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 467
FS-3
General Description
FRONT SUSPENSION
B: COMPONENT
•
Except for STI model
(1)
Front crossmember
(11) Cotter pin
Tightening torque: N·m (kgf-m, ft-lb)
(2)
Crossmember support plate
(12) Castle nut
T1: 25 (2.5, 18.4)
(3)
Stabilizer
(13) Front arm
T2: 38 (3.9, 28.0)
(4)
Bushing
(14) Ball joint
T3: 39 (4.0, 28.8)
(5)
Bracket
(15) Rear bushing
T4: 50 (5.1, 36.9)
(6)
Flange nut
(16) Stud bolt
T5: 60 (6.1, 44.3)
(7)
Flange nut
(17) Stopper
T6: 95 (9.7, 70.1)
(8)
Stabilizer link
(18) Housing
T7: 110 (11.2, 81.1)
(9)
Bolt
(19) Support plate
T8: 150 (15.3, 110.6)
(10) Front bushing
FS-00465
(12)
T6
T6
T4
T7
T8
T7
T2
T2
(1)
(6)
(7)
(3)
(2)
(7)
(7)
(7)
T5
T5
(18)
(15)
(9)
T3
(13)
(11)
(10)
(14)
(16)
(17)
T1
(5)
(4)
T1
(19)
(8)
(9)
(9)
(6)
FS-4
General Description
FRONT SUSPENSION
•
STI model
(1)
Front crossmember
(10) Front bushing
Tightening torque: N·m (kgf-m, ft-lb)
(2)
Crossmember support plate
(11) Cotter pin
T1: 25 (2.5, 18.4)
(3)
Stabilizer
(12) Castle nut
T2: 38 (3.9, 28.0)
(4)
Bushing
(13) Front arm
T3: 39 (4.0, 28.8)
(5)
Bracket
(14) Ball joint
T4: 50 (5.1, 36.9)
(6)
Flange nut
(15) Pillow ball bushing
T5: 60 (6.1, 44.3)
(7)
Flange nut
(16) Housing
T6: 95 (9.7, 70.1)
(8)
Stabilizer link
(17) Support plate
T7: 140 (14.3, 103.3)
(9)
Bolt
T8: 150 (15.3, 110.6)
FS-00497
(14)
T6
T6
T4
T8
T2
T2
(1)
(7)
(8)
(3)
(2)
(7)
(7)
T5
T5
(16)
(10)
T3
(15)
(13)
(12)
(17)
T1
(5)
(4)
T1
(6)
(9)
(9)
(9)
T7
(9)
(11)
(6)
FS-5
General Description
FRONT SUSPENSION
•
Strut
C: CAUTION
• Wear appropriate work clothing, including a cap, protective goggles and protective shoes when performing
any work.
• Before removal, installation or disassembly, be sure to clarify the failure. Avoid unnecessary removal, in-
stallation, disassembly and replacement.
• Use SUBARU genuine grease etc. or equivalent. Do not mix grease etc. of different grades or manufac-
turers.
• Before securing a part on a vise, place cushioning material such as wood blocks, aluminum plate, or cloth
between the part and the vise.
• Be sure to tighten fasteners including bolts and nuts to the specified torque.
• Place shop jacks or rigid racks at the specified points.
(1)
Dust seal
(7)
Helper (standard damper only)
Tightening torque: N·m (kgf-m, ft-lb)
(2)
Self-locking nut
(8)
Coil spring
T1: 20 (2.0, 14.8)
(3)
Strut mount
(9)
Strut (standard damper)
T2: 55 (5.6, 40.6)
(4)
Spacer
(10) Strut (inverted damper)
T3: 155 (15.8, 114.3)
(5)
Upper spring seat
(11) Flange nut
(6)
Dust cover
FS-00447
(1)
(7)
(3)
(2)
(9)
T2
(5)
(4)
T1
(6)
(8)
(2)
T3
(11)
(10)
FS-6
General Description
FRONT SUSPENSION
D: PREPARATION TOOL
1. SPECIAL TOOL
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
927680000
INSTALLER &
REMOVER SET
Used for replacing front arm front bushing.
20099AE020
INSTALLER &
REMOVER
Used for replacing pillow ball bushing of alumi-
num front arm.
28099PA010
HOUSING STAND
• Used for removing pillow ball bushing of alumi-
num front arm.
• Used together with INSTALLER & REMOVER
(20099AE020).
18723AA000
REMOVER
• Used for assembling pillow ball bushing of alu-
minum front arm.
• Used together with INSTALLER & REMOVER
(20099AE020).
ST-927680000
ST20099AE020
ST28099PA010
ST18723AA000
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст