Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 725
SL-49
Transmitter
SECURITY AND LOCKS
23.Transmitter
A: REMOVAL
1. TRANSMITTER BATTERY
CAUTION:
To prevent static electricity damage to the key-
less transmitter printed circuit board, touch the
steel area of building with hand to discharge
static electricity carried on body or clothes be-
fore disassembling the keyless transmitter.
Remove the battery (1) from the transmitter.
B: INSTALLATION
Install each part in the reverse order of removal.
C: INSPECTION
1. TRANSMITTER BATTERY
1) Check the voltage between the transmitter bat-
tery (+) terminal and (–) terminal.
NOTE:
Battery discharge occurs during the inspection.
Complete the measurement within 5 seconds.
2) Replace the battery if the inspection result is not
within the standard value. (Use CR2025 or equiva-
lent.)
D: REPLACEMENT
1. REGISTRATION OF KEYLESS TRANS-
MITTER WITH SUBARU SELECT MONITOR
NOTE:
• A maximum of four keyless transmitter can be
registered for each individual vehicle.
• When replacing or adding the keyless transmit-
ter, new registration of transmitter is necessary.
1) Prepare the Subaru Select Monitor kit. <Ref. to
SL-7, SPECIAL TOOL, PREPARATION TOOL,
2) Prepare PC with Subaru Select Monitor in-
stalled.
3) Connect the USB cable to SDI (Subaru Diagno-
sis Interface) and USB port on the personal com-
puter (dedicated port for the Subaru Select
Monitor).
NOTE:
The dedicated port for the Subaru Select Monitor
means the USB port which was used to install the
Subaru Select Monitor.
4) Connect the diagnosis cable to SDI.
5) Connect SDI to data link connector located in the
lower portion of the instrument panel (on the driv-
er’s side).
CAUTION:
Do not connect scan tools other than the Suba-
ru Select Monitor.
6) Start the PC.
7) Turn the ignition switch to ON (engine OFF) and
run the “PC application for Subaru Select Monitor”.
(A) Resistance 47 Ω
Tester connection
Standard
(+)
(–)
Battery
Positive terminal
Battery
Ground terminal
2.5 — 3.0 V
(1)
SL-00387
(A)
SL-00066
EN-05692
EN-06148
SL-50
Transmitter
SECURITY AND LOCKS
8) On the «Main Menu» of the Subaru Select Mon-
itor, select the {Each System Check} → {Integ. unit
mode} → {Keyless ID registration}.
9) Input the 8-digit ID number attached to the tag
plate of the transmitter or inside the transmitter,
from left to right. Press the [OK] key.
10) The ID number you have entered will be
shown. Make sure that the ID number shown is the
same as that of plastic bag or inside of transmitter.
11) Press the [OK] key if the ID number is correct.
Press the [EXIT] key if incorrect, to return to the
step 3) and enter the ID number again.
12) «ID is being registered···» is displayed and reg-
istration starts.
13) «ID registration completed » will be displayed
when the registration process is done.
14) To exit, select «Quit: NO» to return to {Keyless
ID registration}. If there are additional keyless
transmitters to be registered, select «The following
are registered: OK» to return to the step 4).
NOTE:
• If the registration fails, «ID cannot register. Try
again.» will be shown. Select the [OK] key to return
to the {Keyless ID registration}. Retry starting from
the step 3).
• «Quit: NO» is shown on the Subaru Select Mon-
itor when fourth keyless transmitter has been regis-
tered. Select the [NO] key to return to {Keyless ID
registration}.
SL-51
Immobilizer Control Module
SECURITY AND LOCKS
24.Immobilizer Control Module
A: NOTE
The control of immobilizer system is carried out in
body integrated unit. Refer to the section on the
body integrated unit for the work procedures.
• Removal: <Ref. to SL-48, REMOVAL, Body Inte-
SL-52
Immobilizer Antenna
SECURITY AND LOCKS
25.Immobilizer Antenna
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the screws and remove the steering
column cover lower.
3) Remove the harness cover lock.
4) Remove the screws and detach the knee protec-
tor.
5) Remove the screws and remove the steering
column cover upper.
6) Remove the instrument panel lower cover. <Ref.
to EI-49, REMOVAL, Instrument Panel Lower Cov-
7) Disconnect the immobilizer antenna connector
(A) and ignition switch lighting connector (B).
8) Loosen the screw and release the lock (D) at op-
posite side using flat tip screwdriver (1), and then
detach the immobilizer antenna (C).
CAUTION:
Do not apply excessive force to remove the im-
mobilizer antenna and lock. Otherwise they
may be broken because those parts are the
products made of a plastic.
B: INSTALLATION
Install each part in the reverse order of removal.
WW-00547
LI-01143
WW-00669
(D)
(1)
SL-00315
(A)
(C)
(B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст