Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 710
SE-9
Front Seat
SEATS
2) Refer to the disassembly procedures for the driv-
er’s seat.
D: ASSEMBLY
CAUTION:
When installing the side airbag module assem-
bly, be sure to put the side airbag module be-
tween backrest cover and airbag guide cloth.
Besides, if the backrest cover is not installed
securely, the side airbag module may not be ac-
tivated properly, therefore keep strictly to the
following procedures.
• Be careful not to stain or damage the back-
rest cover during assembly.
• Do not reuse hog rings.
• Secure the hog ring using hog ring pliers.
• Install the hog rings to the specified points
securely and make sure that there is no wrinkle
or twisting on backrest cover.
1) Make sure that there is no foreign matter on side
airbag module.
2) Assemble the seat cover.
(1) Adjust so that the left and right clearances
between wire and seat pad become equal, and
mark the seat pad.
(2) Mark the center of the wire on the pad side
to which the hog ring is attached.
(3) Insert the wire into the seat cover, and align
the wire with the position marked in step 1).
(A) Airbag guide cloth
(B) Backrest cover
(C) Side airbag module ASSY
(1) Backrest frame ASSY
(2) Airbag guide cloth
(3) Backrest cover
(4) Side airbag module ASSY
(5) Hexagon cap nut
SE-00798
(B)
(B)
(B)
(B)
(B)
(B)
(C)
(A)
(A)
(A)
(A)
(A)
(A)
AB-01905
(2)
(1)
(5)
(4)
(3)
(1) Marking
(1) Marking
SE-01259
(1)
SE-01260
(1)
SE-01261
SE-10
Front Seat
SEATS
(4) Mark the wire on the seat cover side accord-
ing to the markings on the seat pad.
(5) Perform steps 1) — 4) to all sections to
which the hog rings are attached.
(6) Make sure that all hog rings (A) are attached
securely.
3) Hereafter, assemble each part in the reverse or-
der of disassembly.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. <Ref. to SE-2, FRONT SEAT LH, COM-
1. DRIVER’S SEAT
NOTE:
• When installing the inner seat belt assembly, fol-
low the procedures described in the seat belt sec-
tion. <Ref. to SB-18, INSTALLATION, Front Seat
• Install the backrest assembly and seat cushion
assembly in the following procedure.
1) Temporarily tighten the reclining hinge bolts.
2) Place the backrest in the most upright position.
3) Tighten the reclining hinge bolts (1) through (4)
in order, in two or three steps by gradually increas-
ing the torque until they reach the specified torque.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. <Ref. to SE-2, FRONT SEAT LH, COM-
4) Assemble each part in the reverse order of dis-
assembly.
5) If any wrinkles are found after the assembly of
the seat cover, finish the seat cover with iron.
(1) Place the wet towel on wrinkles.
(1) Marking
SE-01262
(1)
SE-01353
: A
(A) Vehicle inside
(B) Vehicle outside
(A)
(B)
(2)
(4)
(3)
(1)
SE-00514
SE-01257
SE-11
Front Seat
SEATS
(2) Touch up with warm iron.
CAUTION:
Keep moving the iron, otherwise the seat cover
surface can be damaged.
NOTE:
This method is available for genuine leather, syn-
thetic leather, cloth, etc.
2. PASSENGER’S SEAT
CAUTION:
Make sure to adhere to the following rules when
assembling the passenger seat. Improper work
procedures can cause the occupant detection
system to not operate properly.
• If the seat cushion cover is removed or re-
placed, make sure to perform occupant detec-
tion system adjustment after installing the seat.
<Ref. to OD(diag)-14, SYSTEM CALIBRATION
(REZEROING), OPERATION, Subaru Select
Failure to do so may prevent the passenger’s
airbag from operating properly.
• The occupant detection system (passenger
seat only) control module, occupant detection
sensor, seat cushion pad and seat cushion
frame are considered as a single seat cushion
pad and frame assembly. Never remove the oc-
cupant detection control module or the occu-
pant detection sensor from the seat cushion
frame.
• If the seat cushion cover is removed, make
sure to replace the hang wire on the seat cush-
ion side with a new wire.
• Make sure to install the hog rings/clips to the
specified locations. Do not reuse hog rings.
1) Assemble the seat cushion in the reverse order
of disassembly.
2) Assemble the backrest in the reverse order of
disassembly.
3) When installing the backrest assembly to the
seat cushion assembly, fill the gap in the front side
of slide rail LH and in the rear side of slide rail RH
with cloth etc. in order to stabilize the seat cushion
assembly.
4) Temporarily tighten the reclining hinge bolts in
the order of (1) through (4) to an extent that the seat
backrest assembly is not held securely.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. <Ref. to SE-2, FRONT SEAT LH, COM-
5) Use the reclining lever to place the backrest in
the most upright position, and check the first lock
position of recliner.
6) Hold the seat cushion assembly securely, and
tighten the reclining hinge bolts in the order de-
scribed above until they reach the specified torque.
CAUTION:
Do not touch the backrest assembly when tight-
ening the reclining hinge bolts.
7) Assemble each harness, inner belt assembly
and each cover in the reverse order of removal.
8) Install the seat assembly.
SE-01258
(A) Vehicle inside
(B) Vehicle outside
SE-00537
(A)
(B)
(2)
(4)
(3)
(1)
SE-00538
SE-12
Front Seat
SEATS
9) If any wrinkles are found after the assembly of
the seat cover, finish the seat cover with iron.
(1) Place the wet towel on wrinkles.
(2) Touch up with warm iron.
CAUTION:
Keep moving the iron, otherwise the seat cover
surface can be damaged.
NOTE:
This method is available for genuine leather, syn-
thetic leather, cloth, etc.
E: INSPECTION
Check that no tear or fray on the backrest cover
and seat cushion cover.
NOTE:
For model with side airbag, if the door side of the
backrest cover is torn or frayed, the side airbag
may not be deployed properly. In this case, replace
the backrest cover.
SE-01257
SE-01258
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст