Subaru Legacy (2005 year). Service manual — part 588
5AT-51
AUTOMATIC TRANSMISSION
Inhibitor Switch
13.Inhibitor Switch
A: INSPECTION
Inhibitor switch cannot be checked, because the in-
hibitor switch is installed on control valve assembly.
When a malfunction occurs, refer to 5AT(diag) sec-
tion. <Ref. to 5AT(diag)-35, DTC P0705 TRANS-
MISSION RANGE SENSOR CIRCUIT (PRNDL
INPUT), Diagnostic Procedure with Diagnostic
Trouble Code (DTC).>
5AT-52
AUTOMATIC TRANSMISSION
Front Vehicle Speed Sensor
14.Front Vehicle Speed Sensor
A: REMOVAL
1) Remove the transmission assembly from vehi-
cle. <Ref. to 5AT-38, REMOVAL, Automatic Trans-
mission Assembly.>
2) Remove the rear vehicle speed sensor.
NOTE:
Secure the harness of the rear vehicle speed sen-
sor to the transmission body using wire etc.
3) Remove the extension case.
4) Remove the intermediate case.
5) Remove the center differential carrier. <Ref. to
5AT-78, REMOVAL, Center Differential Carrier.>
6) Lay along the transmission case, and then re-
move the oil pan.
7) Remove the old gasket on the oil pan and trans-
mission case completely.
8) Disconnect the front vehicle speed sensor con-
nector.
9) Remove the front vehicle speed sensor securing
bolt.
10) Remove the front vehicle speed sensor through
the hole of AT transmission main case.
B: INSTALLATION
1) Install the front vehicle speed sensor.
Tightening torque:
7 N
⋅
m (0.7 kgf-m, 5.2 ft-lb)
2) Connect the front vehicle speed sensor connec-
tor.
3) Apply proper amount of liquid gasket to the en-
tire oil pan mating surface.
AT-01950
AT-01951
AT-01952
AT-01953
AT-01954
AT-01954
5AT-53
AUTOMATIC TRANSMISSION
Front Vehicle Speed Sensor
Liquid gasket:
THREE BOND 1217B (Part No. K0877YA020)
4) Install the oil pan by equally tightening the bolts.
Tightening torque:
5 N
⋅
m (0.5 kgf-m, 3.7 ft-lb)
5) Install the center differential carrier. <Ref. to
5AT-78, INSTALLATION, Center Differential Carri-
er.>
6) Install the intermediate case.
Tightening torque:
25 N
⋅
m (2.5 kgf-m, 18.4 ft-lb)
7) Install the extension case.
Tightening torque:
25 N
⋅
m (2.5 kgf-m, 18.4 ft-lb)
8) Install the rear vehicle speed sensor.
Tightening torque:
7 N
⋅
m (0.7 kgf-m, 5.2 ft-lb)
9) Install the transmission assembly into vehicle.
<Ref. to 5AT-42, INSTALLATION, Automatic
Transmission Assembly.>
10) Pour ATF through the oil charge pipe. <Ref. to
5AT-28, REPLACEMENT, Automatic Transmis-
sion Fluid.>
11) Check the level and leaks of ATF. <Ref. to 5AT-
28, INSPECTION, Automatic Transmission Fluid.>
AT-01955
AT-01952
AT-01951
AT-01950
5AT-54
AUTOMATIC TRANSMISSION
Rear Vehicle Speed Sensor
15.Rear Vehicle Speed Sensor
A: REMOVAL
1) Set the vehicle on a lift.
2) Disconnect the ground cable from battery.
3) Remove the intercooler. (Turbo model)
<Ref. to IN(H4DOTC)-12, REMOVAL, Intercool-
er.>
4) Remove the air intake chamber. (Non-turbo
model) <Ref. to IN(H6DO)-7, REMOVAL, Air Intake
Chamber.>
5) Disconnect the following connectors.
• Turbo model
(1) Transmission harness connectors
(2) Front oxygen (A/F) sensor
• Non-turbo model
6) Remove the transmission harness connector
and front oxygen (A/F) sensor connector from the
stay.
7) Lift-up the vehicle.
8) Clean the transmission exterior.
9) Drain the ATF completely. <Ref. to 5AT-28, RE-
PLACEMENT, Automatic Transmission Fluid.>
10) Remove the center exhaust pipe, rear exhaust
pipe and muffler. (Turbo model)
<Ref. to EX(H4DOTC)-6, REMOVAL, Center Ex-
haust Pipe.> <Ref. to EX(H4DOTC)-11, REMOV-
AL, Rear Exhaust Pipe.> <Ref. to EX(H4DOTC)-
12, REMOVAL, Muffler.>
11) Remove the rear exhaust pipe and muffler.
(Non-turbo model) <Ref. to EX(H6DO)-7, REMOV-
AL, Rear Exhaust Pipe.> <Ref. to EX(H6DO)-9,
REMOVAL, Muffler.>
12) Remove the heat shield cover.
13) Remove the propeller shaft. <Ref. to DS-10,
REMOVAL, Propeller Shaft.>
14) Place the transmission jack under transmis-
sion.
NOTE:
Make sure that the support plate of transmission
jack does not touch the crossmember.
15) Remove the transmission rear crossmember
bolt.
IN-00203
AT-01364
AT-01379
(1) Front oxygen (A/F) sensor
(2) Transmission harness connectors
AT-02025
(1)
(2)
AT-01377
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст