Subaru Legacy (2005 year). Service manual — part 151
EN(H4SO 2.0)(diag)-193
ENGINE (DIAGNOSTICS)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
7
CHECK SENSOR OUTPUT.
Measure the voltage between ECM connector
terminals.
Connector & terminal
(B137) No. 23 (+) — (B136) No. 18 (
−
):
Is the voltage less than 4.8 V? Go to step 8.
8
CHECK POOR CONTACT.
Check poor contact in connector between
ECM and electronic throttle control.
Is there poor contact?
Repair the poor
contact.
9
CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Disconnect the connectors from electronic
throttle control.
4) Measure the resistance between ECM con-
nector and electronic throttle control connector.
Connector & terminal
(B137) No. 23 — (E78) No. 5:
(B137) No. 24 — (E78) No. 2:
LHD model
(B136) No. 17 — (E78) No. 4:
RHD model
(B136) No. 17 — (E78) No. 6:
Is the resistance less than 1
Ω?
Repair the open
circuit of harness
connector.
10
CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
Measure the resistance between ECM connec-
tor and chassis ground.
Connector & terminal
(B136) No. 17 — Chassis ground:
(B137) No. 23 — Chassis ground:
(B137) No. 24 — Chassis ground:
Is the resistance more than 1
M
Ω?
Repair the ground
short circuit of har-
ness.
11
CHECK SENSOR POWER SUPPLY.
1) Connect the ECM connector.
2) Turn the ignition switch to ON.
3) Measure the voltage between electronic
throttle control connector and engine ground.
Connector & terminal
LHD model
(E78) No. 4 (+) — Engine ground (
−
):
RHD model
(E78) No. 6 (+) — Engine ground (
−
):
Is the voltage 4.5 — 5.5 V?
Repair the poor
contact in ECM
connector.
Replace the ECM
if defective. <Ref.
to FU(H4SO 2.0)-
34, Engine Con-
trol Module
(ECM).>
12
CHECK SHORT CIRCUIT INSIDE THE ECM.
1) Turn the ignition switch to OFF.
2) Measure the resistance between electronic
throttle control connector and engine ground.
Connector & terminal
(E78) No. 2 — Engine ground:
(E78) No. 5 — Engine ground:
Is the resistance more than 10
Ω?
Repair the poor
contact in ECM
connector.
Replace the ECM
if defective. <Ref.
to FU(H4SO 2.0)-
34, Engine Con-
trol Module
(ECM).>
13
CHECK SENSOR OUTPUT.
1) Connect all the connectors.
2) Turn the ignition switch to ON.
3) Read the data of main throttle sensor signal
using Subaru Select Monitor.
NOTE:
For detailed operation procedure, refer to
“READ CURRENT DATA FOR ENGINE”. <Ref.
to EN(H4SO 2.0)(diag)-25, Subaru Select Mon-
itor.>
Is the voltage 0.5 — 1.0 V?
Step
Check
Yes
No
EN(H4SO 2.0)(diag)-194
ENGINE (DIAGNOSTICS)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
14
CHECK SENSOR OUTPUT.
Read the data of sub throttle sensor signal
using Subaru Select Monitor.
NOTE:
For detailed operation procedure, refer to
“READ CURRENT DATA FOR ENGINE”. <Ref.
to EN(H4SO 2.0)(diag)-25, Subaru Select Mon-
itor.>
Is the voltage 0.5 — 1.0 V?
15
CHECK POOR CONTACT.
Check poor contact in connector between
ECM and electronic throttle control.
Is there poor contact?
Repair the poor
contact.
16
CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Disconnect the connectors from electronic
throttle control.
4) Measure the resistance between ECM con-
nector and electronic throttle control connector.
Connector & terminal
(B137) No. 23 — (E78) No. 5:
(B137) No. 24 — (E78) No. 2:
LHD model
(B136) No. 18 — (E78) No. 1:
RHD model
(B136) No. 18 — (E78) No. 3:
Is the resistance less than 1
Ω?
Repair the open
circuit of harness
connector.
17
CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Connect the ECM connector.
2) Measure the resistance between electronic
throttle control connector and engine ground.
Connector & terminal
LHD model
(E78) No. 1 — Engine ground:
RHD model
(E78) No. 3 — Engine ground:
Is the resistance less than 5
Ω?
Repair the poor
contact in ECM
connector.
Replace the ECM
if defective. <Ref.
to FU(H4SO 2.0)-
34, Engine Con-
trol Module
(ECM).>
18
CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Turn the ignition switch to ON.
2) Measure the voltage between electronic
throttle control connector and engine ground.
Connector & terminal
LHD model
(E78) No. 4 (+) — Engine ground (
−
):
RHD model
(E78) No. 6 (+) — Engine ground (
−
):
Is the voltage less than 10 V?
Repair the battery
short circuit of har-
ness between
ECM connector
and electronic
throttle control
connector.
19
CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
Measure the voltage between electronic throt-
tle control connector and engine ground.
Connector & terminal
(E78) No. 5 (+) — Engine ground (
−
):
(E78) No. 2 (+) — Engine ground (
−
):
Is the voltage less than 10 V?
Repair the short
circuit of harness
between ECM
connector and
electronic throttle
control connector.
Step
Check
Yes
No
EN(H4SO 2.0)(diag)-195
ENGINE (DIAGNOSTICS)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
20
CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Turn the ignition switch to OFF.
2) Remove the ECM.
3) Measure the resistance between ECM con-
nectors.
Connector & terminal
(B137) No. 23 — (B136) No. 17:
(B137) No. 24 — (B136) No. 17:
Is the resistance more than 1
M
Ω?
Repair the short
circuit to sensor
power supply.
21
CHECK SENSOR OUTPUT.
1) Turn the ignition switch to OFF.
2) Connect the connectors except for electric
throttle control relay.
3) Turn the ignition switch to ON.
4) Read the data of main throttle sensor signal
using Subaru Select Monitor.
NOTE:
For detailed operation procedure, refer to
“READ CURRENT DATA FOR ENGINE”. <Ref.
to EN(H4SO 2.0)(diag)-25, Subaru Select Mon-
itor.>
Is the voltage 0.5 — 1.0 V?
Repair the poor
contact of elec-
tronic throttle con-
trol connector.
Replace the elec-
tronic throttle con-
trol if defective.
22
CHECK SENSOR OUTPUT.
Read the data of sub throttle sensor signal
using Subaru Select Monitor.
NOTE:
For detailed operation procedure, refer to
“READ CURRENT DATA FOR ENGINE”. <Ref.
to EN(H4SO 2.0)(diag)-25, Subaru Select Mon-
itor.>
Is the voltage 0.5 — 1.0 V?
Repair the poor
contact in ECM
connector.
Replace the elec-
tronic throttle con-
trol if defective.
23
CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL MO-
TOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Disconnect the connectors from electronic
throttle control.
4) Measure the resistance between ECM con-
nector and electronic throttle control connector.
Connector & terminal
LHD model
(B137) No. 2 — (E78) No. 3:
(B137) No. 3 — (E78) No. 3:
(B137) No. 4 — (E78) No. 6:
(B137) No. 5 — (E78) No. 6:
RHD model
(B137) No. 2 — (E78) No. 1:
(B137) No. 3 — (E78) No. 1:
(B137) No. 4 — (E78) No. 4:
(B137) No. 5 — (E78) No. 4:
Is the resistance less than 1
Ω?
Repair the open
circuit of harness
connector.
Step
Check
Yes
No
EN(H4SO 2.0)(diag)-196
ENGINE (DIAGNOSTICS)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
24
CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL MO-
TOR.
1) Connect the connector to ECM.
2) Turn the ignition switch to ON.
3) Measure the voltage between electronic
throttle control connector and engine ground.
Connector & terminal
LHD model
(E78) No. 3 (+) — Engine ground (
−
):
(E78) No. 6 (+) — Engine ground (
−
):
RHD model
(E78) No. 1 (+) — Engine ground (
−
):
(E78) No. 4 (+) — Engine ground (
−
):
Is the voltage less than 10 V?
Repair the power
supply short cir-
cuit of harness
between ECM and
electronic throttle
control.
25
CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL MO-
TOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Measure the resistance between electronic
throttle control connector and engine ground.
Connector & terminal
LHD model
(E78) No. 3 — Engine ground:
(E78) No. 6 — Engine ground:
RHD model
(E78) No. 1 — Engine ground:
(E78) No. 4 — Engine ground:
Is the resistance more than 1
M
Ω?
Repair the short
circuit of harness.
26
CHECK ELECTRONIC THROTTLE CON-
TROL MOTOR HARNESS.
Measure the resistance between electronic
throttle control connector terminals.
Connector & terminal
LHD model
(E78) No. 3 — (E78) No. 6:
RHD model
(E78) No. 1 — (E78) No. 4:
Is the resistance more than 1
M
Ω?
Repair the short
circuit of harness.
27
CHECK ELECTRONIC THROTTLE CON-
TROL GROUND CIRCUIT.
Measure the resistance between ECM connec-
tor and chassis ground.
Connector & terminal
(B137) No. 1 — Chassis ground:
(B134) No. 2 — Chassis ground:
Is the resistance less than 10
Ω?
Repair the open
circuit of harness.
28
CHECK ELECTRONIC THROTTLE CON-
TROL.
Measure the resistance between electronic
throttle control terminals.
Terminals
LHD model
No. 3 — No. 6:
RHD model
No. 1 — No. 4:
Is the resistance less than 5
Ω?
Replace the elec-
tronic throttle con-
trol.
Step
Check
Yes
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст