Subaru Legacy (2005 year). Service manual — part 417
LU(H6DO)-11
LUBRICATION
Oil Pan and Strainer
6. Oil Pan and Strainer
A: REMOVAL
NOTE:
Before removing the oil pan upper, remove the en-
gine from vehicle. <Ref. to ME(H6DO)-34, RE-
MOVAL, Engine Assembly.> <Ref. to ME(H6DO)-
65, REMOVAL, Cylinder Block.>
1) Set the vehicle on a lift.
2) Lift-up the vehicle.
3) Remove the under cover.
4) Drain the engine oil. <Ref. to LU(H6DO)-7, RE-
PLACEMENT, Engine Oil.>
5) Insert the oil pan cutter blade between oil pan
upper and oil pan lower.
CAUTION:
Do not use a screwdriver or similar tool in place
of oil pan cutter.
6) Remove the oil pan lower.
7) Remove the oil strainer.
B: INSTALLATION
CAUTION:
Before installing the oil pan, wipe clean the
mating surface of oil pan lower and oil pan up-
per.
1) Install the oil strainer onto oil pan upper.
NOTE:
Replace the O-ring with a new one.
Tightening torque:
6.4 N
⋅
m (0.65 kgf-m, 4.7 ft-lb)
2) Apply liquid gasket to the mating surfaces, and
install the oil pan.
Liquid gasket:
THREE BOND 1280B (Part No. K0877YA018)
Liquid gasket applying diameter:
5.0
±
1.0 mm (0.197
±
0.039 in)
LU-00123
LU-02108
LU-02108
LU-00125
LU(H6DO)-12
LUBRICATION
Oil Pan and Strainer
3) Tighten the oil pan lower installing bolts in the
numerical order as shown in the figure.
Tightening torque:
6.4 N
⋅
m (0.65 kgf-m, 4.7 ft-lb)
4) Install the under cover.
5) Fill engine oil. <Ref. to LU(H6DO)-7, INSPEC-
TION, Engine Oil.>
C: INSPECTION
Visually check the oil pan, oil strainer and oil strain-
er stay for damage.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
LU-00126
LU(H6DO)-13
LUBRICATION
Oil Pressure Switch
7. Oil Pressure Switch
A: REMOVAL
1) Set the vehicle on a lift.
2) Disconnect the ground cable from battery.
3) Lift-up the vehicle.
4) Remove the under cover.
5) Disconnect the terminal from oil pressure switch.
6) Remove the oil pressure switch.
B: INSTALLATION
1) Apply liquid gasket to the oil pressure switch
threads.
Liquid gasket:
THREE BOND 1324 (Part No. 004403042) or
equivalent
2) Install the oil pressure switch.
Tightening torque:
25 N
⋅
m (2.5 kgf-m, 18.4 ft-lb)
3) Connect the terminal of oil pressure switch.
4) Install the under cover.
C: INSPECTION
Check that no oil is leaking or seeping from where
the oil pressure switch is installed.
IN-00203
LU-00127
LU-00128
LU-00129
LU-00128
LU-00127
LU(H6DO)-14
LUBRICATION
Engine Oil Filter
8. Engine Oil Filter
A: REMOVAL
1) Lift-up the vehicle.
2) Drain the engine oil by removing engine oil drain
plug.
3) Remove the under cover.
4) Remove the oil filter using ST.
ST
4985447000
OIL FILTER WRENCH
B: INSTALLATION
1) Clean the oil filter installing surface of oil cooler.
2) Obtain a new oil filter and apply a thin coat of en-
gine oil to the seal rubber.
3) Install the oil filter turning it by hand, being care-
ful not to damage the seal rubber.
4) Tighten further (approx. 3/4 turn) after the seal
rubber contacts oil cooler. Do not tighten exces-
sively, or oil may leak.
5) Install the under cover.
6) Lower the vehicle.
7) Fill engine oil. <Ref. to LU(H6DO)-7, INSPEC-
TION, Engine Oil.>
C: INSPECTION
1) After installing the oil filter, run engine and make
sure that no oil is leaking around the seal rubber.
NOTE:
The filter element and filter case are permanently
jointed; therefore, interior cleaning is not neces-
sary.
2) Check the engine oil level. <Ref. to LU(H6DO)-
7, INSPECTION, Engine Oil.>
LU-02011
LU-02035
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст