Subaru Legacy (2005 year). Service manual — part 714
REAR SUSPENSION
RS
Page
General Description . . . . . . . . . . . . . . . . . . . . . 2
Wheel Alignment . . . . . . . . . . . . . . . . . . . . . . .8
Rear Stabilizer. . . . . . . . . . . . . . . . . . . . . . . .9
Rear Arm. . . . . . . . . . . . . . . . . . . . . . . . ...10
Upper Link. . . . . . . . . . . . . . . . . . . . . . . . .14
Rear Shock Absorber. . . . . . . . . . . . . . . . . . . . 16
Front Link . . . . . . . . . . . . . . . . . . . . . . . . ..18
Rear Link. . . . . . . . . . . . . . . . . . . . . . . . ...19
Sub Frame Support Arm . . . . . . . . . . . . . . . . . . ...21
Sub Frame Support Plate. . . . . . . . . . . . . . . . . . ..22
Rear Sub Frame. . . . . . . . . . . . . . . . . . . . . . 23
Helper. . . . . . . . . . . . . . . . . . . . . . . . . . 24
General Diagnostic Table. . . . . . . . . . . . . . . . . . ..25
RS-2
REAR SUSPENSION
General Description
1. General Description
A: SPECIFICATION
NOTE:
• Front and rear toe-ins and front camber can be
adjusted. If the toe-in or camber tolerance exceeds
specifications, adjust them.
• Other items indicated in the specification table
cannot be adjusted. If other items exceed specifica-
tions, check the suspension parts and connections
for deformation, and replace with new ones as re-
quired.
Model
Sedan
Wagon
2.0 i, 2.5 i
2.0 GT
3.0 R
3.0 R
spec. B
2.0 i, 2.5 i
2.0 GT,
3.0 R
3.0 R
spec. B
OUTBACK
2.5 i,
OUTBACK
3.0 R
Wheel arch height
[Tolerance:
+12 mm
−24
mm
(
+0.47 in
−0.94 in
)]
mm (in)
360 (14.2)
375 (14.8)
365
(14.4)
430 (16.9)
Camber (Tolerance:
±0°45′Dif-
ferences between RH and LH:
45
′ or less)
−0°45′
−0°30′
−0°40′
0
°00′
Toe-in
mm (in)
0
±3 (0±0.12) Toe angle (sum of both wheels): 0°±0°15′
Thrust angle (Tolerance:
±0°30′)
0
°
Diameter of stabilizer
mm (in)
17.3
(0.68)
19.1
(0.75)
17.3 (0.68)
19.1 (0.75)
17.3 (0.68)
(1) Front
A
− B = Positive: Toe-in, Negative: Toe-out
α = Each toe angle
FS-00001
B
A
(1)
RS-3
REAR SUSPENSION
General Description
B: COMPONENT
1. REAR SUSPENSION
(1)
Shock absorber
(14)
Rear arm bracket
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(2)
Self-locking nut
(15)
Hub bearing unit
T1: 30 (3.1, 22.4)
(3)
Stabilizer
(16)
Helper
T2: 32 (3.3, 24)
(4)
Stabilizer bushing
(17)
Upper link
T3: 40 (4.1, 30)
(5)
Bracket
(18)
Upper link bushing (inner side)
T4: 44 (4.5, 32.5)
(6)
Stabilizer link
(19)
Upper link bushing (outer side)
T5: 57 (5.8, 42)
(7)
Rear link
(20)
Front link
T6: 62 (6.3, 46)
(8)
Adjusting bolt
(21)
Rear sub frame
T7: 65 (6.6, 48)
(9)
Rear link bushing
(22)
Sub frame support arm
T8: 80 (8.2, 59)
(10)
Adjusting washer
(23)
Sub frame support plate
T9: 120 (12.2, 89)
(11)
Rear arm
T10: 125 (12.7, 92)
(12)
Rear arm rear bushing
T11: 150 (15.3, 111)
(13)
Rear arm front bushing
T12: 175 (17.8, 129)
RS-00137
(1)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
(21)
(23)
(22)
T5
T10
T8
T12
T11
T7
T5
T7
T9
T2
T12
T12
T5
T6
T1
T3
T4
T7
RS-4
REAR SUSPENSION
General Description
2. SHOCK ABSORBER
C: CAUTION
• Wear work clothing, including a cap, protective
goggles and protective shoes during operation.
• Before discarding shock absorbers, be sure to
bleed gas completely. Also, do not throw away in
fire.
• Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly and replacement.
• Use SUBARU genuine grease etc. or equivalent.
Do not mix grease etc. with that of another grade or
from other manufacturers.
• Before securing a part on a vise, place cushion-
ing material such as wood blocks, aluminum plate,
or cloth between the part and the vise.
• Be sure to tighten fasteners including bolts and
nuts to the specified torque.
• Place shop jacks or rigid racks at the specified
points.
(1)
Mount
(4)
Coil spring
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(2)
Upper rubber sheet
(5)
Shock absorber
T1: 30 (3.1, 22.4)
(3)
Dust cover
(6)
Self-locking nut
T2: 35 (3.6, 26)
T3: 62 (6.3, 46)
RS-00037
(4)
(5)
(6)
(6)
(6)
(3)
(2)
(1)
T3
T2
T1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст