Subaru Legacy (2005 year). Service manual — part 301
LU(H4DOTC)-3
LUBRICATION
General Description
Recommended oil:
API standard SL, SJ with “Energy Conserv-
ing” logo is printed (If SL, SJ grade is not
available, use SH grade)
ACEA standard A1, A2 or A3
ILSAC standard GF-3 “Star burst mark” label
on the container
The proper viscosity oil make the engine ideal tem-
perature, and cranking speed increased by reduc-
ing viscaus friction in hot condition.
CAUTION:
When replenishing oil, it does not matter if the
oil to be added is a different brand from that in
the engine; however, use oil having the API
standard and SAE viscosity No. designated by
SUBARU.
NOTE:
If the vehicle is used in areas with very high temper-
atures or for other heavy duty applications, the fol-
lowing viscosity oils must be used: API standard:
SL or SJ
SAE viscosity No.: 30, 40, 10W-50, 20W-40, 20W-
50
(1) SAE viscosity No. and applicable temperature
(2) Recommended
LU-00239
( C)
-30 -20 -15
0
15
30
40
-22
-4
5
32
59
86 104
SAE (1)
( F)
10W-30, 10W-40
5W-30 (2)
LU(H4DOTC)-4
LUBRICATION
General Description
B: COMPONENT
(1)
Plug
(14)
O-ring
(28)
Drain plug
(2)
Gasket
(15)
Oil pump ASSY
(29)
O-ring
(3)
Relief valve spring
(16)
Oil pressure switch
(30)
Oil filler cap
(4)
Relief valve
(17)
Oil filler duct
(31)
Seal
(5)
Oil seal
(18)
O-ring
(6)
Oil pump case
(19)
Rocker cover
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(7)
Inner rotor
(20)
Baffle plate
T1: 5 (0.5, 3.7)
(8)
Outer rotor
(21)
O-ring
T2: 5.4 (0.55, 4.0)
(9)
Oil pump cover
(22)
Oil strainer
T3: 6.4 (0.65, 4.7)
(10)
Oil filter
(23)
Gasket
T4: 10 (1.0, 7.4)
(11)
Oil cooler connector (DOHC turbo
MT model)
(24)
Oil level gauge guide
T5: 44 (4.5, 33)
(25)
Oil pan
T6: 69 (7.0, 50.9)
(12)
Water bypass pipe (DOHC turbo
MT model)
(26)
Oil level gauge
T7: 25 (2.5, 18.4)
(27)
Metal gasket
T8: 54 (5.5, 40)
(13)
Oil cooler (DOHC turbo MT
model)
LU-02145
T7
T2
T1
T4
T5
(9)
(8)
(7)
(6)
(22)
(21)
(23)
(30)
(17)
(16)
(26)
(5)
(4)
(3)
(2)
(1)
T1
T4
(20)
T5
(28)
(25)
(27)
(24)
(29)
T3
(18)
(19)
T8
(11)
(12)
(10)
T3
(13)
T5
(14)
(15)
T3
T3
(31)
LU(H4DOTC)-5
LUBRICATION
General Description
C: CAUTION
• Wear work clothing, including a cap, protective
goggles and protective shoes during operation.
• Remove contamination including dirt and corro-
sion before removal, installation or disassembly.
• Keep the disassembled parts in order and pro-
tect them from dust and dirt.
• Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly and replacement.
• Be careful not to burn yourself, because each
part on the vehicle is hot after running.
• Be sure to tighten fasteners including bolts and
nuts to the specified torque.
• Place shop jacks or rigid racks at the specified
points.
• Before disconnecting connectors of sensors or
units, be sure to disconnect the ground cable from
battery.
LU(H4DOTC)-6
LUBRICATION
General Description
D: PREPARATION TOOL
1. SPECIAL TOOL
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
499977400
CRANK PULLEY
WRENCH
Used for stopping rotation of crank pulley when
removing and tightening crank pulley bolt.
499587100
OIL SEAL
INSTALLER
Used for installing oil seal into oil pump.
18332AA000
OIL FILTER
WRENCH
Used for removing and installing oil filter. (Outer
diameter: 68 mm (2.68 in))
18332AA010
OIL FILTER
WRENCH
Used for removing and installing oil filter. (Outer
diameter: 65 mm (2.56 in))
ST-499977400
ST-499587100
ST18332AA000
ST18332AA010
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст