Subaru Legacy (2005 year). Service manual — part 708
FS-3
FRONT SUSPENSION
General Description
2. WAGON MODEL
NOTE:
• Front and rear toe-ins and front camber can be
adjusted. If the toe-in or camber tolerance exceeds
specifications, adjust them.
• Other items indicated in the specification table
cannot be adjusted. If other items exceed specifica-
tions, check the suspension parts and connections
for deformation, and replace with new ones as re-
quired.
Model
2.0 i
2.5 i
2.0 GT
3.0 R
3.0 R spec.
B
OUTBACK
2.5 i,
OUTBACK
3.0 R
Front
Wheel arch height
(Tolerance:
+12 mm
−24 mm
(
+0.47 in
−0.94 in
))
mm (in)
381 (15.0)
376 (14.8)
372 (14.6)
429 (16.9)
Camber (Tolerance:
±0°45′Differ-
ences between RH and LH 45
′ or
less)
−0°15′
−0°20′
−0°25′
−0°30′
Caster (Referential Value)
5
°45′
6
°05′
5
°05′
Steering angle (Toler-
ance:
±1.5°)
Inner
wheel
37.3
°
37.2
°
37.1
°
37.8
°
Outer
wheel
33.0
°
32.9
°
32.8
°
33.5
°
Toe-in
mm (in)
0
±3 (0±0.12) Toe angle (sum of both wheels): 0°±0°15′
Kingpin angle (Referential Value)
13
°45′
13
°50′
12
°25′
Diameter of stabilizer
mm (in)
20 (0.79)
21 (0.84)
21 (0.83)
Rear
Wheel arch height
(Tolerance:
+12 mm
−24 mm
(
+0.47 in
−0.94 in
))
mm (in)
375 (14.8)
365 (14.4)
430 (16.9)
Camber (Tolerance:
±0°45′Differ-
ences between RH and LH 45
′ or
less)
−0°30′
−0°40′
0
°00′
Toe-in
mm (in)
0
±3 (0±0.12) Toe angle (sum of both wheels): 0°±0°15′
Thrust angle (Tolerance:
±0°30′)
0
°
Diameter of stabilizer
mm (in)
19.1 (0.75)
17.3 (0.68)
(1) Front
A
− B = Positive: Toe-in, Negative: Toe-out
α = Each toe angle
FS-00001
B
A
(1)
FS-4
FRONT SUSPENSION
General Description
B: COMPONENT
(1)
Front crossmember
(14)
Crossmember support plate
(Small type)
(27)
Jack-up plate (6MT model)
(2)
Housing
(3)
Ball joint
(15)
Jack-up plate
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(4)
Front arm
(16)
Dust seal
T1: 20 (2.0, 14.5)
(5)
Support plate
(17)
Strut mount
T2: 25 (2.5, 18.4)
(6)
Rear bushing
(18)
Upper spring seat
T3: 39 (4.0, 28.8)
(7)
Front bushing
(19)
Dust cover
T4: 45 (4.6, 33.2)
(8)
Stud bolt
(20)
Helper
T5: 50 (5.1, 36.9)
(9)
Stabilizer link
(21)
Coil spring
T6: 60 (6.1, 44.3)
(10)
Bracket
(22)
Damper strut
T7: 70 (7.1, 51.6)
(11)
Bushing
(23)
Adjusting bolt
T8: 95 (9.7, 70.1)
(12)
Stabilizer
(24)
Castle nut
T9: 110 (11.2, 81.1)
(13)
Crossmember support plate
(Large type)
(25)
Self-locking nut
T10: 150 (15.3, 110.6)
(26)
Cotter pin
T11: 175 (17.8, 129)
FS-00185
T1
T11
T7
T8
T8
T5
T9
T10
T9
T4
T2
T6
T4
(16)
(25)
(17)
(18)
(19)
(1)
(20)
(21)
(22)
(23)
(25)
(27)
(9)
(10)
(11)
(12)
(13)
(15)
(25)
(25)
(25)
T2
T6
(25)
(14)
(25)
T6
T6
T6
T6
(2)
(5)
(8)
(7)
T3
(3)
(4)
(24)
(26)
(6)
FS-5
FRONT SUSPENSION
General Description
C: CAUTION
• Wear work clothing, including a cap, protective
goggles and protective shoes during operation.
• Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly and replacement.
• Use SUBARU genuine grease etc. or equivalent.
Do not mix grease etc. with that of another grade or
from other manufacturers.
• Before securing a part on a vise, place cushion-
ing material such as wood blocks, aluminum plate,
or cloth between the part and the vise.
• Be sure to tighten fasteners including bolts and
nuts to the specified torque.
• Place shop jacks or rigid racks at the specified
points.
D: PREPARATION TOOL
1. SPECIAL TOOL
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
927380002
ADAPTER
Used as an adapter for camber & caster gauge
when measuring camber and caster.
(1) 28199AC000 PLATE
(2) 28199AC010 BOLT
927680000
INSTALLER &
REMOVER SET
Used for replacing the front arm front bushing.
20299AG000
REMOVER
Used for replacing the front arm rear bushing.
Used with BASE (20999AG010).
(1)
(2)
ST-927380002
ST-927680000
ST20299AG000
FS-6
FRONT SUSPENSION
General Description
2. GENERAL TOOL
20299AG010
BASE
Used for replacing the front arm rear bushing.
Used with REMOVER (20999AG000).
20299AG020
STUD BOLT
SOCKET
Used for removing and installing stud bolt for
front arm installing portion.
20399AG000
STRUT MOUNT
SOCKET
Used for disassembling and assembling strut
mount.
TOOL NAME
REMARKS
Alignment gauge
Used for wheel alignment measurement.
Turning radius gauge
Used for wheel alignment measurement.
Toe-in gauge
Used for toe-in measurement.
Dial gauge
Used for damper strut measurement.
Coil spring compressor
Used for strut assembly/disassembly.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST20299AG010
ST20299AG020
ST20399AG000
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст