Subaru Legacy (2005 year). Service manual — part 642
5MT-15
MANUAL TRANSMISSION AND DIFFERENTIAL
General Description
7. FRONT DIFFERENTIAL
(1)
Drive pinion shaft
(7)
Differential bevel pinion
(13)
Retainer lock plate
(2)
Hypoid driven gear
(8)
Roller bearing
(3)
Pinion shaft
(9)
Differential case
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(4)
Straight pin
(10)
Oil seal
T1: 25 (2.5, 18.4)
(5)
Washer
(11)
Differential side retainer
T2: 62 (6.3, 45.6)
(6)
Differential bevel gear
(12)
O-ring
MT-01365
(12)
(10)
(1)
(2)
T1
T2
(5)
(5)
(6)
(9)
(7)
(7)
(12)
(8)
(8)
(13)
(13)
(11)
(11)
(10)
T1
(4)
(3)
5MT-16
MANUAL TRANSMISSION AND DIFFERENTIAL
General Description
8. TRANSMISSION MOUNTING
(1)
Pitching stopper
(8)
Center crossmember
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(2)
Spacer
(9)
Front crossmember
T1: 70 (7.1, 51.6)
(3)
Cushion rubber
(10)
Cushion (crossmember)
T2: 35 (3.6, 26)
(4)
Front plate
T3: 50 (5.1, 36.9)
(5)
Rear cushion rubber
T4: 58 (5.9, 42.8)
(6)
Rear crossmember
T5: 70 (7.1, 51.6)
(7)
Cushion D
T6: 140 (14.3, 103)
MT-00998
(1)
T4
T1
T5
T5
T2
T6
T2
T3
(2)
(4)
(5)
(10)
(8)
(7)
(3)
(2)
(3)
(6)
(3)
(9)
5MT-17
MANUAL TRANSMISSION AND DIFFERENTIAL
General Description
C: CAUTION
• Wear work clothing, including a cap, protective
goggles and protective shoes, during operation.
• Remove contamination including dirt and corro-
sion before removal, installation or disassembly.
• Keep the disassembled parts in order and pro-
tect them from dust and dirt.
• Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly and replacement.
• When disassembling the case and other light al-
loy parts, use a plastic hammer to force it apart. Do
not pry it apart with a screwdriver or other tool.
• Be careful not to burn yourself, because each
part on the vehicle is hot after running.
• Use SUBARU genuine gear oil, grease etc. or
equivalent. Do not mix gear oil, grease etc. with
that of another grade or from other manufacturers.
• Be sure to tighten fasteners including bolts and
nuts to the specified torque.
• Place shop jacks or rigid racks at the specified
points.
• Apply gear oil onto sliding or revolution surfaces
before installation.
• Replace deformed or damaged snap rings with
new ones.
• Before installing O-rings or oil seals, apply suffi-
cient amount of gear oil to avoid damage and defor-
mation.
• Be careful not to incorrectly install or fail to install
O-rings, snap rings and other such parts.
• Before securing a part on a vice, place cushion-
ing material such as wood blocks, aluminum plate
or cloth between the part and the vice.
• Avoid damaging the mating surface of the case.
• Before applying sealant, completely remove the
old seal.
D: PREPARATION TOOL
1. SPECIAL TOOL
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
399411700
ACCENT BALL
INSTALLER
Used for installing reverse shifter rail arm.
899524100
PULLER SET
Used for removing and installing roller bearing
(Differential).
(1) Puller
(2) Cap
ST-399411700
ST-899524100
5MT-18
MANUAL TRANSMISSION AND DIFFERENTIAL
General Description
399780104
WEIGHT
Used for measuring preload on roller bearing.
498077000
REMOVER
Used for removing roller bearing of drive pinion
shaft.
498077300
CENTER DIFFER-
ENTIAL BEARING
REMOVER
Used for removing the center differential cover
ball bearing.
498147001
DEPTH GAUGE
Used for adjusting main shaft axial end play.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST-399780104
ST-498077000
ST-498077300
ST-498147001
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст