Subaru Legacy (2005 year). Service manual — part 918
AB(diag)-109
AIRBAG SYSTEM (DIAGNOSTICS)
Diagnostic Chart with Trouble Code
AK:DTC 91 CURTAIN AIRBAG MODULE RH FAILURE
DTC DETECTING CONDITION:
• Curtain airbag harness (RH) circuit is faulty.
• Curtain airbag module (RH) is faulty.
• Airbag control module is faulty.
CAUTION:
• Before diagnosing the airbag system, be sure to turn the ignition switch OFF, disconnect the
ground cable from battery, and wait more than 20 seconds before starting to work.
• When replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and check that the warning light operates properly.
• When inspecting the airbag main harness, disconnect the airbag module connector of the driver’s
and passenger’s seats for safety reasons.
• When inspecting the airbag rear harness, disconnect the side airbag module connector, curtain
airbag module connector, seat belt pretensioner connector and lap seat belt pretensioner connector
for safety reasons.
WIRING DIAGRAM:
AB-01258
AB18
AB33
AB40
1
2
6
5
AB34
20
19
4
18
3
4
1
2
AB18
AB33
1 2
AIRBAG CONTROL MODULE
CURTAIN AIRBAG
MODULE RH
CURTAIN AIRBAG
SENSOR RH
7 8 9 10 11 12
13 14 15 16 17 18 19
5 6
20
1 2
3 4
AB34
1 2 3 4
AB(diag)-110
AIRBAG SYSTEM (DIAGNOSTICS)
Diagnostic Chart with Trouble Code
Step
Check
Yes
No
1
CHECK CURTAIN AIRBAG MODULE.
1) Turn the ignition switch OFF, disconnect the
battery ground cable, and wait more than 20
seconds.
2) Disconnect the connector (AB33) from
(AB40), and connect the connector (1F) in test
harness F to connector (AB33).
3) Connect the airbag resistor to connector
(3F) in the test harness F.
4) Connect the battery ground cable and turn
the ignition switch to ON.
Does the airbag warning light
illuminate for 6 seconds and go
off?
Replace the cur-
tain airbag mod-
ule (RH). <Ref. to
AB-20, Curtain Air-
bag Module.>
2
CHECK AIRBAG REAR HARNESS (CUR-
TAIN AIRBAG MODULE HARNESS RH).
1) Turn the ignition switch OFF, disconnect the
battery ground cable, and wait more than 20
seconds.
2) Disconnect the connector (AB26) from seat
belt pretensioner (RH).
3) For the model with lap seat belt preten-
sioner, disconnect the connector (AB30) from
lap seat belt pretensioner.
4) Disconnect the connector (AB24) from side
airbag module (RH).
5) Disconnect the airbag resistor from the test
harness F.
6) Disconnect the connector (AB18) from air-
bag control module.
7) Connect the connector (1U) in the test har-
ness U to connector (AB18).
8) Measure the resistance between connector
(5U) in the test harness U and connector (3F)
in the test harness F.
Connector & terminal
(5U) No. 6 — (3F) No. 4:
(5U) No. 8 — (3F) No. 3:
Is the resistance less than 10
Ω?
Replace the airbag
rear harness with
body harness.
3
CHECK AIRBAG REAR HARNESS (CUR-
TAIN AIRBAG MODULE HARNESS RH).
Measure the resistance between connector
(5U) terminals in the test harness U.
Connector & terminal
(5U) No. 6 — (5U) No. 8:
Is the resistance more than 1
M
Ω?
Replace the airbag
rear harness with
body harness.
4
CHECK AIRBAG REAR HARNESS (CUR-
TAIN AIRBAG MODULE HARNESS RH).
Measure the resistance between the terminals
of connector (3F) in the test harness F.
Connector & terminal
(3F) No. 3 — (3F) No. 4:
Is the resistance more than 1
M
Ω?
Replace the airbag
control module.
<Ref. to AB-22,
Airbag Control
Module.>
Replace the airbag
rear harness with
body harness.
AB(diag)-111
AIRBAG SYSTEM (DIAGNOSTICS)
Diagnostic Chart with Trouble Code
AL:DTC 92 CURTAIN AIRBAG MODULE LH FAILURE
DTC DETECTING CONDITION:
• Curtain airbag harness (LH) circuit is faulty.
• Curtain airbag module (LH) is faulty.
• Airbag control module is faulty.
CAUTION:
• Before diagnosing the airbag system, be sure to turn the ignition switch OFF, disconnect the
ground cable from battery, and wait more than 20 seconds before starting to work.
• When replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and check that the warning light operates properly.
• When inspecting the airbag main harness, disconnect the airbag module connector of the driver’s
and passenger’s seats for safety reasons.
• When inspecting the airbag rear harness, disconnect the side airbag module connector, curtain
airbag module connector and seat belt pretensioner connector for safety reasons.
WIRING DIAGRAM:
AB-01259
AB32
1
2
11
12
AB31
AB39
15
1
14
13
3
4
1
2
AB31
1 2
AB17
AB17 AIRBAG CONTROL MODULE
CURTAIN AIRBAG
MODULE LH
CURTAIN AIRBAG
SENSOR LH
7 8 9 10 11 12
13 14 15 16 17 18 19
5 6
20
1 2
3 4
AB32
1 2 3 4
AB(diag)-112
AIRBAG SYSTEM (DIAGNOSTICS)
Diagnostic Chart with Trouble Code
Step
Check
Yes
No
1
CHECK CURTAIN AIRBAG MODULE.
1) Turn the ignition switch OFF, disconnect the
battery ground cable, and wait more than 20
seconds.
2) Disconnect the connector (AB31) from
(AB39), and connect the connector (1F) in test
harness F to connector (AB31).
3) Connect the airbag resistor to connector
(3F) in the test harness F.
4) Connect the battery ground cable and turn
the ignition switch to ON.
Does the airbag warning light
illuminate for 6 seconds and go
off?
Replace the cur-
tain airbag mod-
ule (LH). <Ref. to
AB-20, Curtain Air-
bag Module.>
2
CHECK AIRBAG REAR HARNESS (CUR-
TAIN AIRBAG MODULE HARNESS LH).
1) Turn the ignition switch OFF, disconnect the
battery ground cable, and wait more than 20
seconds.
2) Disconnect the connector (AB21) from seat
belt pretensioner (LH).
3) Disconnect the connector (AB19) from side
airbag module (LH).
4) Disconnect the airbag resistor from the test
harness F.
5) Disconnect the connector (AB17) from air-
bag control module.
6) Connect the connector (1U) in the test har-
ness U to connector (AB17).
7) Measure the resistance between connector
(5U) in the test harness U and connector (3F)
in the test harness F.
Connector & terminal
(5U) No. 1 — (3F) No. 3:
(5U) No. 3 — (3F) No. 4:
Is the resistance less than 10
Ω?
Replace the airbag
rear harness with
body harness.
3
CHECK AIRBAG REAR HARNESS (CUR-
TAIN AIRBAG MODULE HARNESS LH).
Measure the resistance between connector
(5U) terminals in the test harness U.
Connector & terminal
(5U) No. 1 — (5U) No. 3:
Is the resistance more than 1
M
Ω?
Replace the airbag
rear harness with
body harness.
4
CHECK AIRBAG REAR HARNESS (CUR-
TAIN AIRBAG MODULE HARNESS LH).
Measure the resistance between the terminals
of connector (3F) in the test harness F.
Connector & terminal
(3F) No. 3 — (3F) No. 4:
Is the resistance more than 1
M
Ω?
Replace the airbag
control module.
<Ref. to AB-22,
Airbag Control
Module.>
Replace the airbag
rear harness with
body harness.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст