Subaru Legacy (2005 year). Service manual — part 729
DI-23
DIFFERENTIALS
General Description
899524100
PULLER SET
• Used for removing differential from side bear-
ing cone.
• For VA-type
(1) PULLER
(2) CAP
498485400
DRIFT
• Used for installing side bearing cone.
• For VA1-type
498505501
DIFFERENTIAL
CARRIER GAUGE
• Used for adjusting pinion height.
• For VA1-type
498447110
DRIFT
• Used for press-fitting the bearing race (front)
of differential carrier.
• For VA1-type
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST-899524100
ST-498485400
ST-498505501
ST-498447110
DI-24
DIFFERENTIALS
General Description
498447150
DUMMY SHAFT
• Used for adjusting pinion height and preload.
• For VA1-type
498515500
REPLACER
• Used for removing rear bearing cone.
• For VA1-type
32285AA000
DUMMY COLLAR
• Used for adjusting pinion height and preload.
• For VA1-type
499705404
SEAT
• Used for removing side bearing race.
• Used with PULLER ASSY (499705401).
• For VA1-type
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST-498447150
ST-498515500
ST32285AA000
ST-499705404
DI-25
DIFFERENTIALS
General Description
2. GENERAL PURPOSE TOOL
499705401
PULLER ASSY
• Used for removing side bearing race.
• Used with SEAT (499705404).
• For VA-type
TOOL NAME
REMARKS
Transmission jack
Used for assembly/disassembly of rear differential.
Puller
Used for removal of side bearing retainer.
Thickness gauge
Used for measuring clearance.
Hexagon wrench
Used for installing and removing filler and drain plug.
Tire lever
Used for removal of rear drive shaft. (VA-type)
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST-499705401
DI-26
DIFFERENTIALS
Differential Gear Oil
2. Differential Gear Oil
A: INSPECTION
1) Remove the filler plug, and then check the gear
oil. If it is contaminated or deteriorated, replace the
gear oil. <Ref. to DI-26, REPLACEMENT, Differen-
tial Gear Oil.>
2) Check that the gear oil level is up to the bottom
of filler plug hole. If the level is low, refill up to the
bottom of filler plug hole.
• Except for VA2-type
• VA2-type
B: REPLACEMENT
1) Lift-up the vehicle.
2) Remove the oil drain plug and filler plug, and
drain the gear oil.
CAUTION:
Be careful not to burn yourself, because gear
oil becomes extremely hot after running.
• Except for VA2-type
• VA2-type
3) Tighten the oil drain plug.
NOTE:
• Apply liquid gasket to the drain plug threads for
T-type.
Liquid gasket:
THREE BOND 1105 (Part No. 004403010) or
equivalent
• Use a new aluminum gasket for VA1-type.
• Use a new metal gasket for VA2-type.
Tightening torque:
T-type
49 N
⋅
m (5.0 kgf-m, 36.2 ft-lb)
VA1-type
34 N
⋅
m (3.5 kgf-m, 25.3 ft-lb)
VA2-type
29 N
⋅
m (3.0 kgf-m, 21.4 ft-lb)
(A) Filler plug
(B) Drain plug
(A) Filler plug
(B) Drain plug
DI-00354
(A)
(B)
(B)
DI-00355
(A)
(A) Filler plug
(B) Drain plug
(A) Filler plug
(B) Drain plug
DI-00356
(A)
(B)
(A)
DI-00357
(B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст