Subaru Legacy (2005 year). Service manual — part 1035
LAN(diag)-19
LAN SYSTEM (DIAGNOSTICS)
Subaru Select Monitor
6) Change the setting with UP/DOWN key and press the [YES] key.
• List of body integrated module registration item
NOTE:
Setting is different depending on grade of vehicle.
CAUTION:
• It is possible to control the original functions of vehicle when registrations of body integrated mod-
ule and function setting are corresponded to vehicle equipment.
• When body integrated module is new one or “Factory” mode, key illumination blinks to show
equipment settings does not completed.
• Be sure not to change Factory initial setting except installation of new body integrated module.
NOTE:
“Factory” mode:
• Body integrated module has not been set yet. It can be recognized by key illumination blinking with ignition
switch turned to ON.
• All body integrated modules as part for repair are set to “Factory” mode. When replacing a body integrated
module, be sure to perform the registration operation.
“Market” mode:
• Each settings of body integrated module have been set. It can be recognized by key ring illumination op-
erating simultaneously with room light and turning off with ignition switch turned to ON.
Data
Initial set-
ting
Registration
Remarks
A/C ECM setting
OFF
ON
Illumination control does not operate if A/C ECM setting
is set to “OFF” in case of model with auto A/C.
OFF
If A/C ECM setting is set to “ON” in case of model with-
out auto A/C, illumination change to night illumination
and it is difficult to be recognized.
P/W ECM setting
OFF
ON
Be sure to set P/W ECM setting to “OFF”.
OFF
Center display failure (OP)
OFF
ON
Information may not be displayed on center display if
Center display failure is set to “OFF” in case of model
with center display.
OFF
Wiperdeicer (OP)
OFF
ON
ON signal does not output with operation of wiper
deicer switch if Wiperdeicer is set to “OFF” in model
with wiper deicer.
OFF
Rear fog light setting (OP)
OFF
ON
Vehicle is controlled in rear fog light equipped mode.
OFF
Vehicle is controlled in rear fog light no-equipped mode.
(Be sure to set to “OFF” in model without rear fog light.)
Factory initial setting (Reset of body
integrated module)
Factory
Factory (Reset)
If Factory initial setting is set to “Factory”, registrations
of items above is changed to “OFF”. Be sure to set to
“Market”.
Market (Settle-
ment)
LAN(diag)-20
LAN SYSTEM (DIAGNOSTICS)
Subaru Select Monitor
7) Perform the Factory setting. On the “ECM cus-
tomizing” display screen of Subaru Select Monitor,
select the {Factory initial setting} and press the
[YES] key.
8) Change the mode from Factory into Market.
9) Replace the immobilizer cartridge, and register
the immobilizer key. (Model with immobilizer)
10) Perform the registration according to the proce-
dures of “IMMOBILIZER TEACHING OPERATION
MANUAL”.
11) When key registration is completed, “Do you
want to register remote engine start?” is displayed.
Press the [NO] key to finish the registration.
12) Perform the function setting (ECM customiz-
ing).
<Ref. to LAN(diag)-21, FUNCTION SETTING
(ECM CUSTOMIZING), OPERATION, Subaru Se-
lect Monitor.>
NOTE:
For details concerning operation procedure, refer
to the SUBARU SELECT MONITOR OPERATION
MANUAL.
7. CLEAR MEMORY MODE
1) On the “Main Menu” display screen, select the
{2. Each System Check} and press the [YES] key.
2) On the “System Selection Menu” display screen,
select the {Integ. unit mode} and press the [YES]
key.
3) Press the [YES] key after the information of body
integrated module type is displayed.
4) On the “Integ. unit mode failure diag” display
screen, select the {Clear Memory} and press the
[YES] key.
5) When the “Done” are shown on the display
screen, turn the ignition switch to OFF.
NOTE:
For details concerning operation procedure, refer
to the SUBARU SELECT MONITOR OPERATION
MANUAL.
8. FREEZE FRAME DATA
NOTE:
• Data stored at the time of trouble occurrence is
shown on display.
• Freeze frame data will be memorized maximum
to 20.
• If freeze frame data is not stored in memory cor-
rectly (caused by low power supply of body inte-
grated module), DTC will be displayed with “?” on
the head of it in the Subaru Select Monitor display.
This shows it may be an unreliable reading.
Display
Contents to be monitored
Clear memory?
Clear function of DTC and
freeze frame data
LAN(diag)-21
LAN SYSTEM (DIAGNOSTICS)
Subaru Select Monitor
9. FUNCTION SETTING (ECM CUSTOMIZING)
1) On the “Main Menu” display screen, select the {Each System Check} and press the [YES] key.
2) On the “System Selection Menu” display screen, select the {Integ. unit mode} and press the [YES] key.
3) On the “Integ. unit mode failure diag” display screen, select the {ECM customizing} and press the [YES]
key.
4) Change the setting with UP/DOWN key and press the [YES] key.
• List of function setting item (ECM customizing)
No.
Data
Initial
setting
value
Customize setting
Remarks
1
Off delay time
Normal
Delay time below can be selected by setting.
After door closed
After key unlock
OFF
0 sec.
0 sec.
Short
3 sec.
10 sec.
Normal
5 sec.
20 sec.
Long
8 sec.
30 sec.
2
Auto lock time
30 sec.
0 — 60 seconds
Workable when Auto locking is set to “ON” and Automatic
locking setup is “ON”. Time can be changed by 10 seconds:
0 (OFF) — 60 (maximum).
3
Rr defogger op. mode
15 min.
15 min.
Rear defogger stops in 15 minutes automatically after
switch is turned to ON.
Continuous
Rear defogger repeats active condition for 15 minutes and
inactive condition for 2 minutes until switch is turned to OFF.
4
Wiper deicer op. mode
15 min.
15 min.
Rear defogger stops in 15 minutes automatically after
switch is turned to ON.
Continuous
Rear defogger repeats active condition for 15 minutes and
inactive condition for 2 minutes until switch is turned to OFF.
5
Security Alarm Setup
OFF
ON
Security alarm (hazard, horn or siren) in active condition
OFF
Security alarm in inactive condition
6
Impact Sensor Setup
OFF
ON
Workable when Impact Sensor Setup is set to “ON” Impact
sensor in active condition
OFF
Impact sensor in inactive condition (Set Impact Sensor
Setup of model without impact sensor to “OFF”.)
7
Alarm monitor delay setting
ON
After doors are locked by keyless entry system operated,
Alarm monitor starts in following time.
ON
Delay time is 30 seconds.
OFF
Delay time is 0 seconds.
8
Lockout prevention
ON
ON
Lockout prevention in inactive condition (Lockout prevention
does not operate if safety knob is locked by hand.)
OFF
Lockout prevention in inactive condition
9
Impact sensor (OP)
OFF
ON
Vehicle is controlled in impact sensor equipped mode. (Set
impact sensor to “OFF” in model without impact sensor. If
impact sensor is set to “ON”, hazard, horn or siren operate
after doors are locked by keyless entry system operated
(Alarm monitor starting).)
OFF
Vehicle is controlled in impact sensor no-equipped mode.
10
Siren setting (OP)
OFF
ON
Siren sounds when alarm operates. (Set siren setting to
“OFF” in model without siren. Horn does not sound if siren
setting is set to “ON”.)
OFF
Horn sounds when alarm operates.
11
Answer-back buzzer setup
ON
ON
Workable when answer-back buzzer setup is set to “ON”.
When lock/unlock is selected by keyless entry system oper-
ated, answer-back buzzer sounds.
OFF
When lock/unlock is selected by keyless entry system oper-
ated, answer-back buzzer does not sound.
LAN(diag)-22
LAN SYSTEM (DIAGNOSTICS)
Subaru Select Monitor
5) After setting, make sure that vehicle equipment is same as the setting changed in the {Current Data Dis-
play & Save}.
CAUTION:
• It is possible to control the original functions of vehicle when settings above are corresponded to
vehicle equipment.
• Do not change the settings except for setting above during operation of equipment setting.
• Be sure not to change Factory initial setting except installation of new body integrated module.
NOTE:
For details concerning operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MAN-
UAL.
12
Hazard answer-back setup
ON
ON
Workable when hazard answer-back setup is set to “ON”.
When lock/unlock is selected by keyless entry system oper-
ated, hazard answer-back buzzer operates.
OFF
When lock/unlock is selected by keyless entry system oper-
ated, hazard answer-back does not operate.
13
Automatic locking setup
ON
ON
Workable when Automatic locking setup is set to “ON”.
Automatic locking operates.
OFF
Automatic locking does not operate.
14
Ans.-back Buzzer
ON
ON
Vehicle is controlled in answer-back buzzer equipped
mode.
OFF
Vehicle is controlled in answer-back buzzer non-equipped
mode. (Set Ans.-back Buzzer to “OFF” in model without
answer back buzzer.)
15
Auto locking
ON
ON
Vehicle is controlled in auto locking equipped mode.
OFF
Vehicle is controlled in auto locking non-equipped mode.
(Set Auto locking to “OFF” in model without auto locking.)
16
Initial Keyless Setting
—
—
—
Execution
Settings of keyless entry system are initialized. (No. 2: 30
sec., No. 11: ON, No. 12: ON, No. 13: ON, No. 14: ON)
17
Initial button setting
—
—
—
Execution
Settings of each function are initialized. (No. 1: Normal, No.
3: 15 min., No. 4: 15 min., No. 8: ON)
18
Initial Security setting
—
—
—
Execution
Settings of security system are initialized. (No. 5: OFF, No.
6: OFF, No. 7: ON, No. 10: OFF)
19
Passive Alarm (Not used)
OFF
ON
Applicable to North America model (If Passive Alarm is set
to “ON”, nothing operates and there is no negative effect.)
OFF
20
Door open warning (preven-
tion of battery run-out)
OFF
ON
If detecting door open for 30 minutes, room light, key illumi-
nation and door warning light are turned off to prevent bat-
tery run-out.
OFF
Room light, key illumination and door warning light is not
turned off.
21
(Specification) Security
setup
ON
Operate the selected security set. (EK model)
OFF
Normally in active condition
No.
Data
Initial
setting
value
Customize setting
Remarks
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст