Subaru Legacy IV (2008 year). Service manual — part 247
EC(H4DOTC)-8
Canister
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
Check that there is no damage or dust on the quick
connector. If necessary, clean the seal surface of
the pipe.
Tightening torque:
8 N·m (0.8 kgf-m, 5.9 ft-lb)
C: INSPECTION
Make sure the canister and canister hoses are not
cracked or loose.
EC-02080
EC(H4DOTC)-9
Purge Control Solenoid Valve
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)
5. Purge Control Solenoid Valve
A: REMOVAL
1. PURGE CONTROL SOLENOID VALVE 1
1) Remove the collector cover.
2) Disconnect the ground cable from battery.
3) Remove the bolts which install purge control so-
lenoid valve 1 to the intake manifold, and discon-
nect the connector from the purge control solenoid
valve 1.
4) Disconnect the evaporation hose from the intake
manifold and fuel pipe assembly.
2. PURGE CONTROL SOLENOID VALVE 2
1) Remove the collector cover.
2) Disconnect the ground cable from battery.
3) Remove the solenoid valve bracket assembly
from intake manifold.
4) Disconnect the connector from purge control so-
lenoid valve 2.
5) Disconnect the evaporation hose from the intake
duct and fuel pipe assembly.
6) Remove the purge control solenoid valve 2 from
the solenoid valve bracket assembly.
IN-00203
EC-02424
IN-00203
EC-00219
EC-02266
EC(H4DOTC)-10
Purge Control Solenoid Valve
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)
B: INSTALLATION
1. PURGE CONTROL SOLENOID VALVE 1
Install in the reverse order of removal.
NOTE:
Connect the evaporation hose as shown in the fig-
ure.
Tightening torque:
6.4 N·m (0.7 kgf-m, 4.7 ft-lb)
2. PURGE CONTROL SOLENOID VALVE 2
Install in the reverse order of removal.
NOTE:
Connect the evaporation hose as shown in the fig-
ure.
Tightening torque:
6.4 N·m (0.7 kgf-m, 4.7 ft-lb)
(A) Purge control solenoid valve 1
(B) Purge control solenoid valve 2
(a) To intake manifold
(b) To intake duct
(c) To fuel pipe
EC-02201
(A)
(B)
(b)
(c)
(c)
(a)
EC-02424
(A) Purge control solenoid valve 1
(B) Purge control solenoid valve 2
(a) To intake manifold
(b) To intake duct
(c) To fuel pipe
EC-02201
(A)
(B)
(b)
(c)
(c)
(a)
EC-02266
EC(H4DOTC)-11
Purge Control Solenoid Valve
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)
Tightening torque:
T1: 17 N·m (1.7 kgf-m, 12.5 ft-lb)
T2: 19 N·m (1.9 kgf-m, 14.0 ft-lb)
C: INSPECTION
Make sure the hoses are not cracked or loose.
EC-02252
T2
T1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст