Subaru Legacy IV (2008 year). Service manual — part 33
FU(H4SO)-21
Intake Manifold
FUEL INJECTION (FUEL SYSTEMS)
11) Install the fuel pipe protector RH.
Tightening torque:
19 N·m (1.9 kgf-m, 14.0 ft-lb)
12) Install the fuel pipe protector LH.
Tightening torque:
19 N·m (1.9 kgf-m, 14.0 ft-lb)
13) Install the plug cord stay.
Tightening torque:
6.4 N·m (0.7 kgf-m, 4.7 ft-lb)
14) Install the EGR valve. <Ref. to FU(H4SO)-29,
INSTALLATION, EGR Valve.>
15) Install the throttle body to intake manifold.
<Ref. to FU(H4SO)-12, INSTALLATION, Throttle
Body.>
16) Install the ignition coil and ignitor assembly.
<Ref. to IG(H4SO)-6, INSTALLATION, Ignition Coil
and Ignitor Assembly.>
17) Install the engine ground terminal to intake
manifold.
Tightening torque:
19 N·m (1.9 kgf-m, 14.0 ft-lb)
E: INSPECTION
Make sure the fuel pipe and fuel hoses are not
damaged and the connections are tightened firmly.
FU-02326
FU-02325
FU-03233
FU-01090
FU(H4SO)-22
Engine Coolant Temperature Sensor
FUEL INJECTION (FUEL SYSTEMS)
4. Engine Coolant Temperature
Sensor
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the generator. <Ref. to SC(H4SO)-14,
REMOVAL, Generator.>
3) Drain engine coolant. <Ref. to CO(H4SO)-13,
DRAINING OF ENGINE COOLANT, REPLACE-
MENT, Engine Coolant.>
4) Disconnect the connectors from the engine cool-
ant temperature sensor.
5) Remove the engine coolant temperature sensor.
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
Use a new gasket.
Tightening torque:
18 N·m (1.8 kgf-m, 13.3 ft-lb)
IN-00203
FU-00055
FU(H4SO)-23
Crankshaft Position Sensor
FUEL INJECTION (FUEL SYSTEMS)
5. Crankshaft Position Sensor
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the bolt which installs crankshaft posi-
tion sensor to cylinder block.
3) Remove the crankshaft position sensor, and
then disconnect the connector from it.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
6.4 N·m (0.7 kgf-m, 4.7 ft-lb)
IN-00203
FU-00056
FU-00057
FU-03811
FU(H4SO)-24
Camshaft Position Sensor
FUEL INJECTION (FUEL SYSTEMS)
6. Camshaft Position Sensor
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Disconnect the connector from the camshaft po-
sition sensor.
3) Remove the bolt which installs camshaft position
sensor to support.
4) Remove the bolt which installs camshaft position
sensor support to camshaft cap LH.
5) Remove the camshaft position sensor and the
camshaft position sensor support as a unit.
6) Remove the camshaft position sensor from the
camshaft position sensor support.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
Camshaft position sensor support
6.4 N·m (0.7 kgf-m, 4.7 ft-lb)
Camshaft position sensor
6.4 N·m (0.7 kgf-m, 4.7 ft-lb)
IN-00203
FU-02714
FU-02724
FU-02725
FU-00179
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст