Subaru Legacy IV (2008 year). Service manual — part 1070
GW-7
General Description
GLASS/WINDOWS/MIRRORS
C: PREPARATION TOOL
1. SPECIAL TOOL
2. GENERAL TOOL
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
1B022XU0
SUBARU SELECT
MONITOR III KIT
Used for setting of each function and trouble-
shooting for electrical system.
61299AE000
SPACER
Used for adjusting the upper end position of the
front door glass. (Glass thickness: 5 mm (0.197
in))
61299AE010
SPACER
Used for adjusting the upper end position of rear
door glass. (Glass thickness: 4 mm (0.157 in))
TOOL NAME
REMARKS
Circuit tester
Used for checking voltage and continuity.
Piano wire
Used for removing the window glass.
Windshield glass knife
Used for removing the window glass.
TORX
®
T20
Used for removing and installing the rearview mirror.
ST1B022XU0
ST61299AE000
ST61299AE010
GW-8
Power Window System
GLASS/WINDOWS/MIRRORS
2. Power Window System
A: WIRING DIAGRAM
<Ref. to WI-160, Power Window System.>
B: INSPECTION
Symptom
Repair order
All power windows do not operate.
1. Fuse (SBF-4)
2. Power window circuit breaker
3. Power window relay
4. Wiring harness
5. Body integrated unit
Particular window does not operate.
1. Power window main switch
2. Power window sub-switch
3. Power window motor
4. Wiring harness
“Window Lock” does not operate.
Power window main switch
GW-9
Power Window Control Switch
GLASS/WINDOWS/MIRRORS
3. Power Window Control
Switch
A: REMOVAL
1. MAIN SWITCH
1) Remove the front door trim.
<Ref. to EI-49, REMOVAL, Door Trim.>
2) Disconnect the harness connector.
3) Remove the screws from the reverse side of the
front door trim to remove the power window main
switch.
2. SUB-SWITCH
1) Remove the door trim. <Ref. to EI-49, REMOV-
AL, Door Trim.>
2) Disconnect the connector.
3) Remove the screws from the reverse side of
door trim to remove the power window sub-switch.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. MAIN SWITCH
Measure the switch resistance.
Replace the main switch if faulty.
GW-00387
GW-00388
Switch
position
Terminal No.
Standard
Driver’s seat
UP
10 and 2
7 and 1
Less than 1
:
OFF
1 and 2
Less than 1
:
DOWN
10 and 1
7 and 2
Less than 1
:
AUTO
DOWN
10 and 1
7 and 2
Less than 1
:
Passenger’s
seat
UP
10 and 14
7 and 11
Less than 1
:
OFF
7 and 14
7 and 11
Less than 1
:
DOWN
10 and 11
7 and 14
Less than 1
:
Rear RH
seat
UP
10 and 13
7 and 12
Less than 1
:
OFF
7 and 13
7 and 12
Less than 1
:
DOWN
10 and 12
7 and 13
Less than 1
:
Rear LH seat
UP
10 and 8
7 and 9
Less than 1
:
OFF
7 and 8
7 and 9
Less than 1
:
DOWN
9 and 10
7 and 8
Less than 1
:
GW-00406
1
2
3
4
5
6
7
8
9
10
11
12
13
14
GW-10
Power Window Control Switch
GLASS/WINDOWS/MIRRORS
2. SUB-SWITCH
Measure the switch resistance.
Replace the sub-switch if faulty.
Switch
position
Terminal No.
Standard
Passenger’s
seat
and
rear seat
UP
2 and 3
4 and 5
Less than 1
:
OFF
1 and 2
4 and 5
Less than 1
:
DOWN
1 and 2
3 and 4
Less than 1
:
GW-00407
1
2
3
4
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст