Subaru Legacy IV (2008 year). Service manual — part 1051
LI-21
Front Fog Light Bulb
LIGHTING SYSTEM
17.Front Fog Light Bulb
A: REMOVAL
1. EXCEPT FOR OUTBACK MODEL
1) Disconnect the ground cable from battery.
2) Disengage the two clips, and then turn over the
lower mud guard.
3) Disconnect the harness connector.
4) Retain the bulb then detach the fog light bulb.
2. OUTBACK MODEL
1) Disconnect the ground cable from the battery.
2) Disengage the two clips, and then turn over the
lower mud guard.
3) Disconnect the harness connector.
4) Remove the back cover.
5) Remove the spring retainer then detach the fog
light bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new part.
LI-00288
LI-00705
LI-00288
LI-00774
LI-22
Side Turn Signal Light Assembly
LIGHTING SYSTEM
18.Side Turn Signal Light
Assembly
A: REMOVAL
1) Disconnect the ground cable from the battery.
2) Remove the scalp cap. <Ref. to GW-19, RE-
PLACEMENT, Scalp Cap.>
3) Remove the mirror. <Ref. to GW-21, REPLACE-
MENT, Outer Mirror.>
4) Disconnect the harness connector, remove the 2
mounting screws and then remove the side turn
signal light assembly.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
0.8 N·m (0.08 kgf-m, 0.59 ft-lb)
C: INSPECTION
1) Install the side turn signal light assembly and
check that it blinks normally.
2) If it does not blink normally, replace the side turn
signal light assembly with a new part.
NOTE:
Since LED (Light Emitting Diode) is used for the
side turn signal light, replace the side turn signal
light assembly if the LED burns out.
LI-00707
LI-23
Rear Combination Light Assembly
LIGHTING SYSTEM
19.Rear Combination Light
Assembly
A: REMOVAL
1. SEDAN MODEL
1) Disconnect the ground cable from the battery.
2) Remove the trunk room side trim. <Ref. to EI-70,
REMOVAL, Trunk Room Trim.>
3) Remove the four nuts, and then detach the rear
combination light after disconnecting the connec-
tor.
2. WAGON MODEL
1) Disconnect the ground cable from the battery.
2) Remove the clips.
3) While pressing the section (A), insert your finger
or a flat tip screwdriver wrapped with tape into the
clearance (B) to remove claws in the order of (C),
(D), (E), and remove the rear combination cover.
4) Remove the two bolts, and then detach the rear
combination light by pulling it to the rear side of ve-
hicle.
5) After turning the sockets of the tail/stop light
bulbs and rear turn signal light bulbs, remove the
rear combination light.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
Sedan model:
4.5 N·m (0.46 kgf-m, 3.3 ft-lb)
Wagon model:
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
LI-00294
LI-00295
LI-00284
(E)
(C)
(D)
(B)
(A)
LI-00296
LI-24
Tail/Stop Light Bulb
LIGHTING SYSTEM
20.Tail/Stop Light Bulb
A: REMOVAL
1. SEDAN MODEL
1) Disconnect the ground cable from the battery.
2) Remove the trunk side trim cover.
3) Turn the socket and remove the bulb.
2. WAGON MODEL
1) Remove the rear combination light assembly.
<Ref. to LI-23, WAGON MODEL, REMOVAL, Rear
Combination Light Assembly.>
2) Turn the socket and remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new part.
LI-00775
LI-00440
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст