Subaru Legacy IV (2008 year). Service manual — part 845
RS-2
General Description
REAR SUSPENSION
1. General Description
A: SPECIFICATION
Refer to “FS” section for rear suspension specifica-
tions. <Ref. to FS-2, SPECIFICATION, General
Description.>
NOTE:
• Front and rear toe-in and front camber can be
adjusted. Adjust if the toe-in or camber tolerance
exceeds specifications.
• Other items indicated in the specifications table
cannot be adjusted. If other items exceed specifica-
tions, check the suspension parts and connections
for deformation, and replace with new parts as re-
quired.
(1) Front
A – B = Positive: Toe-in, Negative: Toe-out
D = Individual toe angles
B
A
(1)
FS-00269
RS-3
General Description
REAR SUSPENSION
B: COMPONENT
1. REAR SUSPENSION
(1)
Shock absorber
(14)
Rear arm bracket
Tightening torque:N·m (kgf-m, ft-lb)
(2)
Self-locking nut
(15)
Helper
T1: 30 (3.1, 22.4)
(3)
Stabilizer
(16)
Upper link
T2: 32 (3.3, 24)
(4)
Stabilizer bushing
(17)
Upper link bushing (inner side)
T3: 38 (3.9, 28)
(5)
Bracket
(18)
Upper link bushing (outer side)
T4: 44 (4.5, 32.5)
(6)
Stabilizer link
(19)
Front link
T5: 57 (5.8, 42)
(7)
Rear link
(20)
Rear sub frame
T6: 60 (6.1, 44)
(8)
Adjusting bolt
(21)
Sub frame support arm
T7: 62 (6.3, 46)
(9)
Rear link bushing
(22)
Sub frame lower stopper
T8: 65 (6.6, 48)
(10)
Adjusting washer
(23)
Spacer
T9: 120 (12.2, 89)
(11)
Rear arm
(24)
Stabilizer link bracket (model with
aluminum rear arm)
T10: 125 (12.7, 92)
(12)
Rear arm rear bushing
T11: 150 (15.3, 111)
(13)
Rear arm front bushing
T12: 175 (17.8, 129)
(1)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
(22)
(22)
(21)
T5
T10
T10
T12
T11
T5
T8
T9
T2
T12
T12
T5
T7
T1
T3
T4
(23)
(24)
T6
RS-00238
RS-4
General Description
REAR SUSPENSION
2. SHOCK ABSORBER
C: CAUTION
• Wear appropriate work clothing, including a cap,
protective goggles and protective shoes when per-
forming any work.
• Before disposing of shock absorbers, be sure to
bleed the gas out completely. Also, do not expose
to flames or fire.
• Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly and replacement.
• Use SUBARU genuine grease etc. or equivalent.
Do not mix grease etc. of different grades or man-
ufacturers.
• Before securing a part on a vise, place cushion-
ing material such as wood blocks, aluminum plate,
or cloth between the part and the vise.
• Be sure to tighten fasteners including bolts and
nuts to the specified torque.
• Place shop jacks or rigid racks at the specified
points.
(1)
Mount
(4)
Coil spring
Tightening torque:N·m (kgf-m, ft-lb)
(2)
Upper rubber sheet
(5)
Shock absorber
T1: 30 (3.1, 22.4)
(3)
Dust cover
(6)
Self-locking nut
T2: 35 (3.6, 26)
T3: 62 (6.3, 46)
RS-00037
(4)
(5)
(6)
(6)
(6)
(3)
(2)
(1)
T3
T2
T1
RS-5
General Description
REAR SUSPENSION
D: PREPARATION TOOL
1. SPECIAL TOOL
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
20099AE000
INSTALLER &
REMOVER
Used for replacing the rear link bushing.
20099AE010
INSTALLER &
REMOVER
Used for replacing the upper link bushing.
20099AE020
INSTALLER &
REMOVER SET
Used for replacing the rear arm front bushing.
20099AE040
INSTALLER &
REMOVER SET
Used for replacing the rear arm rear bushing.
ST20099AE000
ST20099AE010
ST20099AE020
ST20099AE040
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст