Subaru Legacy IV (2008 year). Service manual — part 1118
SL-45
Trunk Lid Release Handle
SECURITY AND LOCKS
16.Trunk Lid Release Handle
A: REMOVAL
1) Remove the cover (A).
2) Remove the trunk lid trim. <Ref. to EI-70, RE-
MOVAL, Trunk Room Trim.>
3) Remove the four clips to remove the trunk lid re-
lease handle.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
Make sure the lever works smoothly.
(A)
SL-00382
SL-00383
SL-46
Front Hood Lock Assembly
SECURITY AND LOCKS
17.Front Hood Lock Assembly
A: REMOVAL
1) Open the front hood.
2) Remove the bolts, and then detach the front
hood lock assembly.
3) Remove the cable from lock assembly.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. <Ref. to SL-4, FRONT HOOD LOCK
AND REMOTE OPENERS, COMPONENT,
General Description.>
NOTE:
Apply grease to the movable part.
C: ADJUSTMENT
Loosen the bolt, and adjust the lock assembly while
moving it up and down.
D: INSPECTION
1) Check the striker for deformation or abnormal
wear.
2) Check the safety lever for improper movement.
3) Check other levers and springs for rust formation
or unsmooth movement.
SL-00287
SL-00290
SL-47
Remote Openers
SECURITY AND LOCKS
18.Remote Openers
A: REMOVAL
1. FRONT HOOD OPENER
1) Remove the cable from the front hood lock as-
sembly.
2) Remove the bolt, and then detach the opener le-
ver.
2. TRUNK LID OPENER
1) Remove the rear seat. <Ref. to SE-18, REMOV-
AL, Rear Seat.>
2) Remove the center pillar lower trim, side sill cov-
er, rear pillar lower trim and floor mat on the driver’s
side. Remove the clip holding the cable.
3) Remove the opener lever (1) and rear cover (2).
4) Remove the pin (3) and remove front cover (4).
5) Remove the bolt and nut, and remove the pull
handle assembly (5).
6) Remove the cable from the pull handle assembly
(5).
7) Remove clamp (7) to remove the key cylinder (8).
CAUTION:
Remove the key cylinder in the UNLOCK position.
8) Remove the trunk lid lock assembly from the
trunk lid.
9) Remove the cable from the trunk lid lock assembly.
SL-00291
(1) Opener lever
(2) Rear cover
(3) Pin
(4) Front cover
(5) Pull handle ASSY
(6) Cable
(7) Clamp
(8) Key cylinder
(1) Trunk lid lock ASSY
(2) Cable
SL-00384
(6)
(8)
(3)
(2)
(1)
(4)
(7)
(5)
SL-00385
(1)
(2)
SL-48
Remote Openers
SECURITY AND LOCKS
3. FUEL FILLER LID OPENER
Sedan model
Refer to the trunk lid opener. <Ref. to SL-47,
TRUNK LID OPENER, REMOVAL, Remote Open-
ers.>
Wagon model
1) Remove the rear seat. <Ref. to SE-18, REMOV-
AL, Rear Seat.>
2) Remove the center pillar lower trim, side sill cov-
er, rear pillar lower trim and floor mat on the driver’s
side. Remove the clip holding the cable.
3) Remove the bolt and nut, and then detach the
pull handle assembly.
4) Remove the cable from pull handle assembly.
5) Remove the rear quarter trim RH. <Ref. to EI-63,
REMOVAL, Rear Quarter Trim.>
6) Rotate the fuel lock inside the quarter panel to
90° and remove. (Either right or left turn)
B: INSTALLATION
Install in the reverse order of removal.
CAUTION:
Install the key cylinder to the trunk lid in the UN-
LOCK position.
C: INSPECTION
Make sure the front hood, trunk lid and fuel filler lid
open and close smoothly.
(1) Cover
(2) Pull handle ASSY
(3) Cable
SL-00386
(2)
(1)
(3)
SL-00265
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст