Subaru Legacy III (2000-2003 year). Service manual — part 767
VDC-104
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH DIAGNOSIS CONNECTOR
18
CHECK GROUND SHORT IN CONTACT
POINT CIRCUIT OF RELAY BOX.
Measure resistance between VDCH/U connec-
tor and chassis ground.
Connector & terminal
(VDC1) No. 2 — Chassis ground:
Does the measured value exceed the specified
value?
1 M
Ω
Replace relay box
and check fuse
No. 8.
19
CHECK BATTERY SHORT IN CONTACT
POINT CIRCUIT OF RELAY BOX.
Measure voltage between VDCH/U connector
and chassis ground.
Connector & terminal
(VDC1) No. 2 (+) — Chassis ground (
−−−−
):
Is the measured value less than the specified
value?
1 V
Replace relay box.
Check fuse No. 8.
20
CHECK BATTERY SHORT IN CONTACT
POINT CIRCUIT OF RELAY BOX.
1) Turn ignition switch to ON.
2) Measure voltage between VDCH/U con-
nector and chassis ground.
Connector & terminal
(VDC1) No. 2 (+) — Chassis ground (
−−−−
):
Is the measured value less than the speci-
fied value?
1 V
Replace relay box.
Check fuse No. 8.
21
CHECK RESISTANCE OF INLET AND CUT
SOLENOID VALVES.
1) Disconnect connector from VDCH/U.
2) Measure resistance between VDCH/U con-
nector terminals.
Connector & terminal
(VDC5) No. 8 — (VDC2) No. 2:
(VDC5) No. 5 — (VDC2) No. 2:
(VDC5) No. 6 — (VDC2) No. 2:
(VDC5) No. 7 — (VDC2) No. 2:
(VDC5) No. 9 — (VDC2) No. 2:
(VDC5) No. 12 — (VDC2) No. 2:
Is the measured value within the specified
range?
8.04 — 9.04
Ω
Replace VDCH/U.
<Ref. to VDC-8,
VDC Control Mod-
ule (VDCCM).>
22
CHECK RESISTANCE OF OUTLET SOLE-
NOID VALVE.
Measure resistance between VDCH/U connec-
tor terminals.
Connector & terminal
(VDC5) No. 4 — (VDC2) No. 2:
(VDC5) No. 1 — (VDC2) No. 2:
(VDC5) No. 2 — (VDC2) No. 2:
(VDC5) No. 3 — (VDC2) No. 2:
(VDC5) No. 10 — (VDC2) No. 2:
(VDC5) No. 11 — (VDC2) No. 2:
Is the measured value within the specified
range?
4.04 — 4.54
Ω
Replace VDCH/U.
<Ref. to VDC-8,
VDC Control Mod-
ule (VDCCM).>
Step
Value
Yes
No
VDC-105
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH DIAGNOSIS CONNECTOR
23
CHECK GROUND SHORT OF SOLENOID
VALVE.
Measure resistance between VDCH/U connec-
tor and chassis ground.
Connector & terminal
(VDC2) No. 2 — Chassis ground:
Does the measured value exceed the specified
value?
1 M
Ω
Replace VDCH/U
and check all
fuses. <Ref. to
VDC-8, VDC Con-
trol Module
(VDCCM).>
24
CHECK BATTERY SHORT OF SOLENOID
VALVE.
Measure voltage between VDCH/U connector
and chassis ground.
Connector & terminal
(VDC2) No. 2 (+) — Chassis ground (
−−−−
):
Is the measured value less than the specified
value?
1 V
Replace VDCH/U
and check all
fuses. <Ref. to
VDC-8, VDC Con-
trol Module
(VDCCM).>
25
CHECK BATTERY SHORT OF SOLENOID
VALVE.
1) Turn ignition switch to ON.
2) Measure voltage between VDCH/U con-
nector and chassis ground.
Connector & terminal
(VDC2) No. 2 (+) — Chassis ground (
−−−−
):
Is the measured value less than the speci-
fied value?
1 V
Replace VDCH/U
and check all
fuses. <Ref. to
VDC-8, VDC Con-
trol Module
(VDCCM).>
26
CHECK BATTERY SHORT OF HARNESS.
1) Turn ignition switch to OFF.
2) Disconnect connector from VDCCM.
3) Measure voltage between VDCCM connec-
tor and chassis ground.
Connector & terminal
(F87) No. 30 (+) — Chassis ground (
−−−−
):
(F87) No. 24 (+) — Chassis ground (
−−−−
):
(F87) No. 23 (+) — Chassis ground (
−−−−
):
(F87) No. 31 (+) — Chassis ground (
−−−−
):
(F87) No. 26 (+) — Chassis ground (
−−−−
):
(F87) No. 25 (+) — Chassis ground (
−−−−
):
(F87) No. 3 (+) — Chassis ground (
−−−−
):
(F87) No. 51 (+) — Chassis ground (
−−−−
):
(F87) No. 50 (+) — Chassis ground (
−−−−
):
(F87) No. 4 (+) — Chassis ground (
−−−−
):
(F87) No. 2 (+) — Chassis ground (
−−−−
):
(F87) No. 29 (+) — Chassis ground (
−−−−
):
Is the measured value less than the speci-
fied value?
1 V
Repair harness
between VDCH/U
and VDCCM and
check all fuses.
Step
Value
Yes
No
VDC-106
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH DIAGNOSIS CONNECTOR
27
CHECK BATTERY SHORT OF HARNESS.
1) Turn ignition switch to ON.
2) Measure voltage between VDCCM connec-
tor and chassis ground.
Connector & terminal
(F87) No. 30 (+) — Chassis ground (
−−−−
):
(F87) No. 24 (+) — Chassis ground (
−−−−
):
(F87) No. 23 (+) — Chassis ground (
−−−−
):
(F87) No. 31 (+) — Chassis ground (
−−−−
):
(F87) No. 26 (+) — Chassis ground (
−−−−
):
(F87) No. 25 (+) — Chassis ground (
−−−−
):
(F87) No. 3 (+) — Chassis ground (
−−−−
):
(F87) No. 51 (+) — Chassis ground (
−−−−
):
(F87) No. 50 (+) — Chassis ground (
−−−−
):
(F87) No. 4 (+) — Chassis ground (
−−−−
):
(F87) No. 2 (+) — Chassis ground (
−−−−
):
(F87) No. 29 (+) — Chassis ground (
−−−−
):
Is the measured value less than the speci-
fied value?
1 V
Repair harness
between VDCH/U
and VDCCM and
check all fuses.
28
CHECK GROUND SHORT OF HARNESS.
1) Turn ignition switch to OFF.
2) Measure resistance between VDCCM con-
nector and chassis ground.
Connector & terminal
(F87) No. 30 — Chassis ground:
(F87) No. 24 — Chassis ground:
(F87) No. 23 — Chassis ground:
(F87) No. 31 — Chassis ground:
(F87) No. 26 — Chassis ground:
(F87) No. 25 — Chassis ground:
(F87) No. 3 — Chassis ground:
(F87) No. 51 — Chassis ground:
(F87) No. 50 — Chassis ground:
(F87) No. 4 — Chassis ground:
(F87) No. 2 — Chassis ground:
(F87) No. 29 — Chassis ground:
Does the measured value exceed the spec-
ified value?
1 M
Ω
Repair harness
between VDCH/U
and VDCCM.
29
CHECK HARNESS/CONNECTOR BETWEEN
VDCCM AND VDCH/U.
1) Connect connector (F91) to VDCH/U.
2) Measure resistance between VDCCM con-
nector and VDCH/U connector.
Connector & terminal
(F87) No. 30 — (VDC2) No. 2:
(F87) No. 24 — (VDC2) No. 2:
(F87) No. 23 — (VDC2) No. 2:
(F87) No. 31 — (VDC2) No. 2:
(F87) No. 26 — (VDC2) No. 2:
(F87) No. 25 — (VDC2) No. 2:
Is the measured value within the specified
range?
8.0 — 10.0
Ω
Repair harness/
connector
between VDCH/U
and VDCCM.
Step
Value
Yes
No
VDC-107
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH DIAGNOSIS CONNECTOR
30
CHECK HARNESS/CONNECTOR BETWEEN
VDCCM AND VDCH/U.
Measure resistance between VDCCM connec-
tor and VDCH/U connector.
Connector & terminal
(F87) No. 3 — (VDC2) No. 2:
(F87) No. 51 — (VDC2) No. 2:
(F87) No. 50 — (VDC2) No. 2:
(F87) No. 4 — (VDC2) No. 2:
(F87) No. 2 — (VDC2) No. 2:
(F87) No. 29 — (VDC2) No. 2:
Is the measured value within the specified
range?
4.0 — 6.0
Ω
Repair harness/
connector
between VDCH/U
and VDCCM.
31
CHECK POOR CONTACT IN CONNECTORS.
Is there poor contact in connector between
VDCCM and VDCH/U?
There is poor contact.
Repair connector.
32
CHECK VDCCM.
1) Connect all connectors.
2) Erase the memory.
3) Perform inspection mode.
4) Read out the diagnostic trouble code.
Is the same diagnostic trouble code as in
the current diagnosis still being output?
Same DTC indicated.
Replace VDCCM.
<Ref. to VDC-8,
VDC Control Mod-
ule (VDCCM).>
33
CHECK ANY OTHER DIAGNOSTIC TROU-
BLE CODES APPEARANCE.
Are other diagnostic trouble codes being out-
put?
Other DTC indicated.
Proceed with the
diagnosis corre-
sponding to the
diagnostic trouble
code.
A temporary poor
contact.
Step
Value
Yes
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст