Subaru Legacy III (2000-2003 year). Service manual — part 756
VDC-60
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH DIAGNOSIS CONNECTOR
N: DTC 29 ABNORMAL ABS SENSOR SIGNAL (ANY ONE OF FOUR)
DIAGNOSIS:
• Faulty ABS sensor signal (noise, irregular signal, etc.)
• Faulty tone wheel
• Wheels turning freely for a long time
TROUBLE SYMPTOM:
• ABS does not operate.
• VDC does not operate.
WIRING DIAGRAM:
VDC00174
F55
F88
B15
B6
2 1
R72
R73
F45
F2
1
2
2
1
7
6
2
1
4
1
3
F88
17
15
12
13
16
14
R
10
L
F45
B62
:
:
F2
B100
:
:
F55
R49
B15
R73
49
19
17
16
14
15
1
55
46
18
1
2
B6
2
1
R72
8
9
11
12
13
VDC CONTROL MODULE
FRONT ABS
SENSOR LH
FRONT ABS
SENSOR RH
LHD
RHD
REAR ABS
SENSOR LH
REAR ABS
SENSOR RH
F87
56 57
59 60
62 63
65
82 83
80
27
28
25
26
23
24
21
22
19
20
17
18
15
16
13
14
11
12
9
10
7
8
5
6
3
4
1
2
54
55
52
53
50
51
81
48
49
46
47
44
45
78
79
76
77
75
42
43
40
41
74
72
73
70
71
39
37
38
35
36
69
67
68
66
33
34
61
64
31
32
29
30
58
F87
: RHD MODEL
:LHD MODEL
R
R
R
L
L
L
1
3
4 5 6
2
1 2
3 4 5
6 7 8 9 10 11 12
1 2 3
4 5 6 7
8 9 10 11 12 13 14 15 16
3 4
1 2
8 9 10 11
12 13 14 15 16 17 18 19 20 21 22 23 24
5 6
7
VDC-61
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH DIAGNOSIS CONNECTOR
Step
Value
Yes
No
1
CHECK IF THE WHEELS HAVE TURNED
FREELY.
Check if the wheels have been turned freely for
more than one minute, such as when the vehi-
cle is jacked-up, under full-lock cornering or
when tire is not in contact with road surface.
Turned freely over 1 minutes.
The VDC is nor-
mal. Erase the
diagnostic trouble
code.
NOTE:
When the wheels
turn freely for a
long time, such as
when the vehicle is
towed or jacked-
up, or when steer-
ing wheel is contin-
uously turned all
the way, this trou-
ble code may
sometimes occur.
2
CHECK TIRE SPECIFICATIONS.
Are the tire specifications correct?
Correct specification.
Replace tire.
3
CHECK WEAR OF TIRE.
Is the tire worn excessively?
Worn excesiblely.
Replace tire.
4
CHECK TIRE PRESSURE.
Is the tire pressure correct?
Correct tire pressure.
Adjust tire pres-
sure.
5
CHECK INSTALLATION OF ABS SENSOR.
Tightening torque:
33
±±±±
10 N·m (3.3
±±±±
1.0 kgf-m, 24
±±±±
7 ft-lb)
Are the ABS sensor installation bolts tightened
securely?
Tightened securely.
Tighten ABS sen-
sor installation
bolts securely.
6
CHECK ABS SENSOR GAP.
Measure tone wheel to pole piece gap over
entire perimeter of the wheel.
Is the measured value within the specified
range?
Front wheel 0.3 - 0.8 mm
(0.012 - 0.031 in) and Rear
wheel 0.44 - 0.94 mm (0.0173 -
0.0370 in)
Adjust the gap.
NOTE:
Adjust the gap us-
ing spacer (Part
No. 26755AA000).
If spacers cannot
correct the gap, re-
place worn sensor
or worn tone
wheel.
7
CHECK OSCILLOSCOPE.
Is an oscilloscope available?
Available.
8
CHECK ABS SENSOR SIGNAL.
1) Raise all four wheels of ground.
2) Turn ignition switch OFF.
3) Remove VDCCM connector cover. <Ref. to
VDC-19, VDCCM Connector Cover.>
4) Connect the oscilloscope to the connector.
5) Turn ignition switch ON.
6) Rotate wheels and measure voltage at
specified frequency. <Ref. to ABS-15,
WAVEFORM, Control Module I/O Signal.>
NOTE:
When this inspection is completed, the VDCCM
sometimes stores the DTC 29.
Connector & terminal
(F87) No. 14 (+) — No. 15 (
−−−−
) (Front RH):
(F87) No. 49 (+) — No. 19 (
−−−−
) (Front LH):
(F87) No. 18 (+) — No. 46 (
−−−−
) (Rear RH):
(F87) No. 16 (+) — No. 17 (
−−−−
) (Rear LH):
Is oscilloscope pattern smooth, as shown in
figure?
Smooth pattern.
VDC-62
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH DIAGNOSIS CONNECTOR
9
CHECK CONTAMINATION OF ABS SENSOR
OR TONE WHEEL.
Remove disc rotor from hub.
Is the ABS sensor pole piece or the tone wheel
contaminated by dirt or other foreign matter?
Dirt or foreign matter found.
Thoroughly
remove dirt or
other foreign mat-
ter.
10
CHECK DAMAGE OF ABS SENSOR OR
TONE WHEEL.
Are there broken or damaged teeth in the ABS
sensor pole piece or the tone wheel?
Broken or damaged.
Replace ABS sen-
sor or tone wheel.
Front <Ref. to
VDC-27, Front
ABS Sensor.> and
<Ref. to VDC-29,
Front Tone
Wheel.> Rear
<Ref. to VDC-28,
Rear ABS Sen-
sor.> and <Ref. to
VDC-30, Rear
Tone Wheel.>
11
CHECK TONE WHEEL RUNOUT.
Measure tone wheel runout.
Is the measured value less than the specified
value?
0.05 mm (0.0020 in)
Repair tone wheel.
Front <Ref. to
VDC-29, Front
Tone Wheel.>
Rear <Ref. to
VDC-30, Rear
Tone Wheel.>
12
CHECK VDCCM.
1) Turn ignition switch to OFF.
2) Connect all connectors.
3) Erase the memory.
4) Perform inspection mode.
5) Read out the diagnostic trouble code.
Is the diagnostic same trouble code as in
the current diagnosis still being output?
Same DTC indicated.
Replace VDCCM.
<Ref. to VDC-8,
VDC Control Mod-
ule (VDCCM).>
13
CHECK ANY OTHER DIAGNOSTIC TROU-
BLE CODES APPEARANCE.
Are other diagnostic trouble codes being out-
put?
Other DTC indicated.
Proceed with the
diagnosis corre-
sponding to the
diagnostic trouble
code.
A temporary poor
contact.
Step
Value
Yes
No
VDC-63
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH DIAGNOSIS CONNECTOR
O: DTC 31 ABNORMAL INLET AND CUT SOLENOID VALVE CIRCUIT(S)
(FRONT RH INLET)
NOTE:
For diagnostic procedure, refer to DTC 62. <Ref. to VDC-64, DTC 62 ABNORMAL INLET AND CUT SOLE-
NOID VALVE CIRCUIT(S) (SECONDARY CUT), Diagnostics Chart with Diagnosis Connector.>
P: DTC 33 ABNORMAL INLET AND CUT SOLENOID VALVE CIRCUIT(S)
(FRONT LH INLET)
NOTE:
For diagnostic procedure, refer to DTC 62. <Ref. to VDC-64, DTC 62 ABNORMAL INLET AND CUT SOLE-
NOID VALVE CIRCUIT(S) (SECONDARY CUT), Diagnostics Chart with Diagnosis Connector.>
Q: DTC 35 ABNORMAL INLET AND CUT SOLENOID VALVE CIRCUIT(S) (REAR
RH INLET)
NOTE:
For diagnostic procedure, refer to DTC 62. <Ref. to VDC-64, DTC 62 ABNORMAL INLET AND CUT SOLE-
NOID VALVE CIRCUIT(S) (SECONDARY CUT), Diagnostics Chart with Diagnosis Connector.>
R: DTC 37 ABNORMAL INLET AND CUT SOLENOID VALVE CIRCUIT(S) (REAR
LH INLET)
NOTE:
For diagnostic procedure, refer to DTC 62. <Ref. to VDC-64, DTC 62 ABNORMAL INLET AND CUT SOLE-
NOID VALVE CIRCUIT(S) (SECONDARY CUT), Diagnostics Chart with Diagnosis Connector.>
S: DTC 61 ABNORMAL INLET AND CUT SOLENOID VALVE CIRCUIT(S) (PRI-
MARY CUT)
NOTE:
For diagnostic procedure, refer to DTC 62. <Ref. to VDC-64, DTC 62 ABNORMAL INLET AND CUT SOLE-
NOID VALVE CIRCUIT(S) (SECONDARY CUT), Diagnostics Chart with Diagnosis Connector.>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст