Subaru Legacy III (2000-2003 year). Service manual — part 449
LU(H4DOSTC)-16
LUBRICATION
OIL PAN AND STRAINER
2) Install oil strainer onto baffle plate.
CAUTION:
Replace O-ring with a new one.
Tightening torque:
10 N·m (1.0 kgf-m, 7 ft-lb)
3) Apply fluid gasket to mating surfaces and install
oil pan.
Fluid gasket:
Part No. 004403007
THREE BOND 1215 or equivalent
4) Mount oil pan on engine block.
Tightening torque:
5 N·m (0.5 kgf-m, 3.6 ft-lb)
5) Lower engine onto front crossmember.
6) Tighten nuts which secure front cushion rubber
onto front crossmember.
Tightening torque:
69 N·m (7.0 kgf-m, 51 ft-lb)
7) Install under cover.
8) Lower the vehicle.
CAUTION:
When lowering vehicle, wire rope must be re-
leased at the same time.
9) Remove lifting device and steel cables.
10) Install pitching stopper.
Tightening torque:
T1: 50 N·m (5.1 kgf-m, 37 ft-lb)
T2: 58 N·m (5.9 kgf-m, 43 ft-lb)
LU-00032
LU-00034
LU-00031
LU-00030
LU-00028
ME-00218
T2
T1
LU(H4DOSTC)-17
LUBRICATION
OIL PAN AND STRAINER
11) Install radiator upper brackets.
12) Install the intercooler. <Ref. to IN(H4DOSTC)-
14, INSTALLATION, Intercooler.>
13) Install the air intake boot and air cleaner upper
cover.
14) Tighten the clamp (A) which connects air intake
boot to intake duct.
15) Lock the two clips (B) to air cleaner upper cov-
er.
16) Connect the connector to mass air flow sensor.
17) Install front wheels.
18) Connect battery ground cable.
19) Fill engine oil. <Ref. to LU(H4DOSTC)-8, IN-
SPECTION, Engine Oil.>
C: INSPECTION
By visual check make sure oil pan, oil strainer, oil
strainer stay and baffle plate are not damaged.
LU-00097
(B)
(A)
LU-00153
LU-00026
FU-00009
LU(H4DOSTC)-18
LUBRICATION
OIL PRESSURE SWITCH
6. Oil Pressure Switch
A: REMOVAL
1) Remove generator from bracket. <Ref. to
SC(H4DOSTC)-14, REMOVAL, Generator.>
2) Disconnect terminal from oil pressure switch.
3) Remove oil pressure switch.
B: INSTALLATION
1) Apply fluid gasket to oil pressure switch threads.
Fluid gasket:
Part No. 004403042
THREE BOND 1324 or equivalent
2) Install oil pressure switch onto engine block.
Tightening torque:
25 N·m (2.5 kgf-m, 18.1 ft-lb)
3) Connect terminal of oil pressure switch.
4) Install generator on bracket. <Ref. to
SC(H4DOSTC)-14, INSTALLATION, Generator.>
C: INSPECTION
Make sure oil does not leak or seep from where the
oil pressure switch is installed.
LU-00036
LU-00037
LU-00038
LU-00037
LU-00036
LU(H4DOSTC)-19
LUBRICATION
ENGINE OIL COOLER
7. Engine Oil Cooler
A: REMOVAL
NOTE:
Equipped only for MT model.
1) Lift-up the vehicle.
2) Remove the under cover.
3) Drain the engine oil.
Set a container under the vehicle, and remove the
drain plug from oil pan.
4) Drain the coolant.
5) Remove the water by-pass pipe between oil
cooler and water pump.
6) Remove the engine oil filter. <Ref. to
LU(H4DOSTC)-21, REMOVAL, Engine Oil Filter.>
7) Remove the connector, and then remove the oil
cooler.
(A) Metal gasket
(B) Drain plug
LU-00151
(B)
(A)
LU-00154
(A) O-ring
(B) Oil cooler
(C) Connector
LU-00155
( A )
( B )
( C )
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст