Subaru Legacy III (2000-2003 year). Service manual — part 615
MT-28
MANUAL TRANSMISSION AND DIFFERENTIAL
GENERAL DESCRIPTION
398527700
PULLER ASSY
• Used for removing and extension case roller
bearing.
• Used for removing front idfferential side
retainer Bearing outer race.
398643600
GAUGE
Used for measuring total end play, extension
end play and drive pinion height.
398177700
INSTALLER
Used for installing bearing cone of transfer
driven gear (transfer case side).
499797000
INSTALLER
Used for installing differential side retainer oil
seal.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST-398527700
ST-398643600
ST-398177700
ST-499797000
MT-29
MANUAL TRANSMISSION AND DIFFERENTIAL
GENERAL DESCRIPTION
398507703
DUMMY COLLAR
• Used for installing input shaft holder oil seal.
• For dual-range model.
398663600
PLIERS
• Used for removing and installing input shaft
snap ring.
• For dual-range model.
499757001
SNAP RING GUIDE
• Used for installing snap ring (OUT 25).
• For dual-range model.
899858600
RETAINER II
• Used for removing ball bearing.
• For dual-range model.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST-398507703
ST-398663600
ST-499757001
ST-899858600
MT-30
MANUAL TRANSMISSION AND DIFFERENTIAL
GENERAL DESCRIPTION
2. GENERAL PURPOSE TOOLS
899474100
EXPANDER
• Used for removing and installing snap ring.
• For dual-range model.
899580100
INSTALLER
• Used when pressing ball bearings into input
shaft.
• For dual-range model.
399513600
INSTALLER
• Used when pressing ball bearings into input
shaft.
• For dual-range model.
TOOL NAME
REMARKS
Circuit Tester
Used for measuring resistance, voltage and ampere.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST-899474100
ST-899580100
ST-399513600
MT-31
MANUAL TRANSMISSION AND DIFFERENTIAL
TRANSMISSION GEAR OIL
2. Transmission Gear Oil
A: INSPECTION
1) Park vehicle on a level surface.
2) Turn ignition switch to OFF.
3) Remove oil level gauge and wipe it clean.
4) Reinsert the level gauge all the way. Be sure
that the level gauge is correctly inserted and in the
proper direction.
5) Pull out the oil level gauge again and check the
oil level is between lower and upper levels. If it is
below the lower level, check oil leakage and add oil
through the oil level gauge hole to bring the level up
to the upper level.
B: REPLACEMENT
1) Pull out oil level gauge.
2) Lift-up the vehicle.
3) Drain transmission gear oil completely.
CAUTION:
• Directly after the engine has been running,
the transmission gear oil is hot. Be careful not
to burn yourself.
• Be careful not to splash transmission gear oil
on exhaust pipe; it may cause smoke or fire. If
transmission gear oil splashes to exhaust
pipes, wipe clean them.
4) Tighten transmission gear oil drain plug with new
gasket.
Tightening torque:
44 N·m (4.5 kgf-m, 32.5 ft-lb)
5) Lower the vehicle.
6) Pour gear oil into the gauge hole.
Recommended gear oil:
Use GL-5 (75W-90) or equivalent.
Gear oil capacity:
Single-range model;
3.5
2
(3.7 US qt, 3.1 Imp qt)
Dual-range model;
4.0
2
(4.2 US qt, 3.5 Imp qt)
7) Check the level of the transmission gear oil, and
confirm that the level is within the specified range
marked on the gauge.
NOTE:
When inserting the level gauge into transmission
gear, align the protrusion on the side of the top part
of the level gauge with the notch in the gauge hole.
(A) OIl level gauge
(B) Upper level
(C) Lower level
PM-00030
(B)
(C)
(A)
(A) Drain plug
(B) Gasket
MT-00061
( A )
( B )
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст