Subaru Legacy III (2000-2003 year). Service manual — part 593
AT-106
AUTOMATIC TRANSMISSION (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC)
Q: DTC 79 TRANSFER DUTY SOLENOID
DIAGNOSIS:
Output signal circuit of transfer duty solenoid is open or shorted.
TROUBLE SYMPTOM:
Excessive “braking” in tight corners.
WIRING DIAGRAM:
AT-00590
-
6
TRANSMISSION
B54
TCM
AT4
6
T4
B11
TRANSFER
DUTY
SOLENOID
B54
1 2
7
8
9
5 6
3 4
10 11 12
19 20 21
13
14 15
16
17
18
22
23
24
B11
1 2
5
6 7
8
13
14 15
16
9 10
11 12
3 4
17 18
19 20
AT-107
AUTOMATIC TRANSMISSION (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC)
Step
Value
Yes
No
1
CHECK HARNESS CONNECTOR BETWEEN
TCM AND TRANSMISSION.
1) Turn ignition switch to OFF.
2) Disconnect connector from TCM and trans-
mission.
3) Measure resistance of harness between
TCM and transmission connector.
Connector & terminal
(B54) No. 6 — (B11) No. 6:
Is the measured value less than the speci-
fied value?
1
Ω
Repair open circuit
in harness
between TCM and
transmission con-
nector.
2
CHECK HARNESS CONNECTOR BETWEEN
TCM AND TRANSMISSION.
Measure resistance harness connector
between TCM and chassis ground.
Connector & terminal
(B54) No. 6 — Chassis ground:
Does the measured value exceed the specified
value?
1 M
Ω
Repair short circuit
in harness
between TCM and
transmission con-
nector.
3
CHECK TRANSFER DUTY SOLENOID.
Measure resistance between transmission
connector and transmission terminals.
Connector & terminal
(T4) No. 6 — No. 16:
Is the measured value within the specified
range?
10 — 17
Ω
4
PREPARE SUBARU SELECT MONITOR.
Do you have a Subaru Select Monitor?
Subaru Select Monitor is avail-
able.
5
CHECK OUTPUT SIGNAL EMITTED FROM
TCM.
1) Connect connectors to TCM and transmis-
sion.
2) Turn ignition switch to ON (engine OFF).
3) Select lever is moved to P range.
4) Throttle is fully closed.
5) Measure voltage between TCM connector
and chassis ground.
Connector & terminal
(B54) No. 6 (+) — Chassis ground (
−−−−
):
Is the measured value less than the speci-
fied value?
1 V
6
CHECK OUTPUT SIGNAL EMITTED FROM
TCM.
1) Select lever is moved to D range.
2) Measure voltage between TCM connector
and chassis ground.
Connector & terminal
(B54) No. 6 (+) — Chassis ground (
−−−−
):
Is the measured value within the specified
range?
5 — 7 V
Even if “POWER”
indicator lights up,
the circuit has
returned to a nor-
mal condition at
this time. A tempo-
rary poor contact
of the connector or
harness may be
the cause. Repair
harness or con-
nector in the trans-
fer duty solenoid
and TCM connec-
tor.
7
CHECK SPECIFICATIONS.
Is VDC system or SPORT shift equipped?
The vehicle is equipped with
the VDC system or SPORT
shift.
AT-108
AUTOMATIC TRANSMISSION (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC)
8
CHECK OUTPUT SIGNAL EMITTED FROM
TCM USING SUBARU SELECT MONITOR.
1) Connect connectors to TCM and transmis-
sion.
2) Connect Subaru Select Monitor to data link
connector.
3) Turn ignition switch to ON (engine OFF)
and turn Subaru Select Monitor switch to
ON.
4) Shift select lever to D and open throttle fully
(vehicle speed 0 km/h or 0 MPH).
5) Read data of transfer duty solenoid using
Subaru Select Monitor.
•Transfer duty solenoid is indicated in “%”.
Is transfer duty solenoid data within the
specified range?
5 — 10%
9
CHECK OUTPUT SIGNAL EMITTED FROM
TCM USING SUBARU SELECT MONITOR.
1) Move select lever to “N” with throttle fully
closed (vehicle speed 0 km/h or 0 MPH).
2) Read data of transfer duty solenoid using
Subaru Select Monitor.
•Transfer duty solenoid is indicated in “%”.
Is transfer duty solenoid data within the
specified range?
Approx. 60 — 70%
Even if “POWER”
indicator lights up,
the circuit has
returned to a nor-
mal condition at
this time. A tempo-
rary poor contact
of the connector or
harness may be
the cause. Repair
harness or con-
nector in the trans-
fer duty solenoid
and TCM connec-
tor.
10
CHECK OUTPUT SIGNAL EMITTED FROM
TCM USING SUBARU SELECT MONITOR.
1) Connect connectors to TCM and transmis-
sion.
2) Connect Subaru Select Monitor to data link
connector.
3) Turn ignition switch to ON (engine OFF)
and turn Subaru Select Monitor switch to
ON.
4) Shift select lever to D and open throttle fully
(vehicle speed 0 km/h or 0 MPH).
5) Read data of transfer duty solenoid using
Subaru Select Monitor.
•Transfer duty solenoid is indicated in “%”.
Is transfer duty solenoid data within the
specified range?
80 — 95%
Step
Value
Yes
No
AT-109
AUTOMATIC TRANSMISSION (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC)
11
CHECK OUTPUT SIGNAL EMITTED FROM
TCM USING SUBARU SELECT MONITOR.
1) Move select lever to “N” with throttle fully
close (vehicle speed 0 km/h or 0 MPH).
2) Rear data of transfer duty solenoid using
Subaru Select Monitor.
•Transfer duty solenoid is indicated in “%”.
Is transfer duty solenoid data the specified
value?
Approx. 40%
Even if “POWER”
indicator lights up,
the circuit has
returned to a nor-
mal condition at
this time. A tempo-
rary poor contact
of the connector or
harness may be
the cause. Repair
harness or con-
nector in the trans-
fer duty solenoid
and TCM connec-
tor.
12
CHECK POOR CONTACT.
Is there poor contact in transfer duty solenoid
circuit?
There is poor contact.
Repair poor con-
tact.
Replace TCM.
<Ref. to AT-76,
Transmission Con-
trol Module
(TCM).>
13
CHECK TRANSFER DUTY SOLENOID (IN
TRANSMISSION).
1) Lift-up the vehicle and place safety stand.
2) Drain automatic transmission fluid.
CAUTION:
Do not drain the automatic transmission flu-
id until it cools down.
3) Remove extension case, and disconnect
connector from transfer duty solenoid.
4) Measure resistance between transfer duty
solenoid connector and transmission
ground.
Connector & terminal
(AT4) No. 1 — Transmission ground:
Is the measured value within the specified
range?
10 — 17
Ω
Replace transfer
duty solenoid.
14
CHECK HARNESS CONNECTOR BETWEEN
TRANSFER DUTY SOLENOID AND TRANS-
MISSION.
Measure resistance of harness between trans-
fer duty solenoid and transmission connector.
Connector & terminal
(T4) No. 6 — (AT4) No. 1:
Is the measured value less than the specified
value?
1
Ω
Repair open circuit
in harness
between transfer
duty solenoid and
transmission con-
nector.
Step
Value
Yes
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст