Subaru Legacy III (2000-2003 year). Service manual — part 960
SE-18
SEATS
REAR SEAT
2) Remove bolts securing lower portion of backrest
and then open the center trunk through lid.
3) Lift rear seat backrest and then remove it.
B: INSTALLATION
1. WAGON
1) Install in the reverse order of removal.
Tightening torque:
Refer to COMPONENT in General Descrip-
tion.
<Ref. to SE-5, REAR SEAT (WAGON),
COMPONENT, GENERAL DESCRIPTION.>
2. SEDAN
1) Hook and fasten the upper-back side of the rear
seat backrest to the body hook.
2) Tighten the bolt and install the backrest.
3) Hook and fasten the seat cushion to the hook on
the lower part of the rear seat backrest.
Tightening torque:
Refer to COMPONENT in General Descrip-
tion.
<Ref. to SE-4, REAR SEAT (SEDAN), COM-
PONENT, General Description.>
C: DISASSEMBLY
1. WAGON
1) Remove rear seat. <Ref. to SE-17, REMOVAL,
Rear Seat.>
2) Remove bolts, and then remove bracket hinge.
3) Remove rear backrest lock cover.
SE-00124
SE-00125
SE-00124
(1) Raise
(2) Hook
(3) Attaching bolt
(4) Hook
(5) Push
SE-00123
A
B
( 1 )
( 2 )
( 3 )
( 4 )
( 5 )
SE-00128
SE-00129
SE-19
SEATS
REAR SEAT
4) While turning counterclockwise rear backrest
knob, remove it.
5) While picking up tip with pliers, remove headrest
lock bushings.
6) Remove backrest hook.
7) Remove hook at bottom.
8) Remove 4 pawls.
9) Remove 8 hog rings (A).
10) Remove the hog rings (A) on front side of cush-
ion pad.
Armrest-equipped seat:
11) Remove cover. When disassembly of rear seat
cushion is required, proceed to the following steps.
SE-00130
SE-00131
SE-00132
SE-00133
SE-00134
SE-00189
: ( A )
SE-00135
: ( A )
SE-00136
: ( A )
SE-20
SEATS
REAR SEAT
12) Remove bolts, and then remove cushion hinge.
Separated-type seat:
Remove clips. Remove bolts, and then remove
cushion hinge.
13) Remove bezel.
14) Remove rear cushion mat.
15) Remove hook, and then remove frame.
16) Remove hog rings (A), and then remove cover.
Separated-type seat:
2. SEDAN
1) Remove the rear seat from the vehicle. <Ref. to
SE-17, REMOVAL, Rear Seat.>
2) Remove the hog rings from around the seat
backrest.
3) Remove the two nuts and remove the armrest
assembly.
SE-00137
SE-00190
SE-00191
SE-00138
SE-00139
SE-00140
: ( A )
SE-00192
: ( A )
SE-00141
SE-21
SEATS
REAR SEAT
4) Remove the hog rings (A), and then remove the
seat cover.
Armrest through-equipped type seat:
Unified-type seat:
5) Remove the hog rings around the seat cushion.
6) Remove the hog rings (A), and then remove the
seat cover
D: ASSEMBLY
1. WAGON
1) Assemble in the reverse order of disassembly.
NOTE:
• Do not contaminate or damage cover.
• While installing wire rings, prevent seat from get-
ting wrinkled.
2. SEDAN
1) Assemble in the reverse order of disassembly.
NOTE:
• Do not contaminate or damage cover.
• While installing wire rings, prevent seat from get-
ting wrinkled.
SE-00142
: ( A )
SE-00193
: ( A )
SE-00194
SE-00144
: ( A )
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст