Subaru Legacy III (2000-2003 year). Service manual — part 994
CC-8
CRUISE CONTROL SYSTEM
CRUISE CONTROL COMMAND SWITCH
5. Cruise Control Command
Switch
A: REMOVAL
WARNING:
Before servicing, be sure to read the notes in
the AB section for proper handling of the driv-
er's airbag module. <Ref. to AB-3, CAUTION,
GENERAL DESCRIPTION.>
1) Set front wheels in straight ahead position.
2) Turn ignition switch OFF.
3) Disconnect ground cable from battery and wait
for at least 20 seconds before starting work.
4) Using TORX
®
BIT T30 (Tamper resistant type),
loosen two TORX
®
bolts which secure driver's air-
bag module.
5) Disconnect airbag module connector on back of
airbag module.
6) Remove horn switch from steering wheel as
shown.
7) Disconnect horn and cruise control command
switch connector, then remove cruise control com-
mand switch.
B: INSTALLATION
Install is in the reverse order of removal.
C: INSPECTION
Measure cruise control command switch resis-
tance.
Check continuity between cruise control command
switch terminals.
If NG, replace cruise control command switch.
CC-00018
TORX BIT T30
R
CC-00019
Switch
Position
Terminal No.
Standard
CANCEL
ON
1 (+) and 2 (
−
)
Less than 1
Ω
ON
1 (+) and 3 (
−
)
Less than 1
Ω
SET/
COAST
OFF
1 and 2
More than 1 M
Ω
ON
1 and 2
Less than 1
Ω
RESUME/
ACCEL
OFF
1 and 3
More than 1 M
Ω
ON
1 and 3
Less than 1
Ω
CC-00020
CC-00021
3 2 1
CC-9
CRUISE CONTROL SYSTEM
STOP AND BRAKE SWITCH
6. Stop and Brake Switch
A: REMOVAL
1) Disconnect ground cable from battery.
2) Disconnect connector from stop and brake
switch, and then remove the switch. <Ref. to BR-
55, REMOVAL, Stop Light Switch.>
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
Measure the brake switch (A) and stop light switch
(B) resistance.
If NG, replace stop and brake switch.
Switch
Pedal
Terminal No.
Standard
Brake
Released
1 and 4
Less than 1
Ω
Depressed
1 and 4
More than 1 M
Ω
Stop light
Released
2 and 3
More than 1 M
Ω
Depressed
2 and 3
Less than 1
Ω
CC-00022
( A )
1
1 2 3 4
3
2
4
( B )
CC-10
CRUISE CONTROL SYSTEM
CLUTCH SWITCH
7. Clutch Switch
A: REMOVAL
1) Disconnect ground cable from battery.
2) Disconnect the connector from the clutch switch,
and then remove the switch. <Ref. to CL-40, RE-
MOVAL, Clutch Switch.>
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
Measure clutch switch resistance.
If NG, replace the clutch switch.
Switch
Pedal
Terminal No.
Standard
Clutch
Released
1 and 2
Less than 1
Ω
Depressed
1 and 2
More than 1 M
Ω
CC-00023
CC-11
CRUISE CONTROL SYSTEM
INHIBITOR SWITCH
8. Inhibitor Switch
A: REMOVAL
1) Disconnect ground cable from battery.
2) Disconnect connector from inhibitor switch, and
then remove the switch. <Ref. to AT-50, REMOV-
AL, Inhibitor Switch.>
B: INSTALLATION
Installation is in the reverse order of removal.
C: INSPECTION
Measure inhibitor switch resistance.
If NG, replace inhibitor switch.
Selector lever position
Terminal No.
Standard
P
7 and 12
Less than 1
Ω
N
Less than 1
Ω
Except P and N
More than 1 M
Ω
CC-00024
1
2
3
4
5
6
7
8
9
10
11
12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст