Subaru BRZ (2012 year). Service manual — part 8
NT-9
Note
NOTE
11.TIE-DOWNS
Tie-downs are used when transporting vehicles and when using the chassis dynamo. Attach tie-down only
to the specified locations on the vehicle.
• Tie-down location
• Chain direction at tie-down condition
CAUTION:
• Pull the front and rear of the vehicle in the opposite direction, and pull the left and right of the ve-
hicle in the same direction.
• Patterns except for the followings (recommended) are not allowed.
(1)
Hook for tie-down
(2)
Tie-down hole
Recommended
Tie-down direction
NT-00453
(2)
(1)
(2)
NT-00214
NT-10
Note
NOTE
• Tie-down range
For ground transportation
CAUTION:
To tie down the vehicle from the vehicle interior, hook the hooks of the tie-down chain on the rear tie-
down holes from the vehicle interior. When the vehicle is tied down from vehicle outside, hook the
hooks of tie-down chain on the rear tie-down hooks from vehicle outside.
(A)
Front tie-down hook
(B)
Rear tie-down hole
(C)
Chain pulling range at tie-down
condition
:(C)
(B)
20˚
(A)
20˚
20˚
20˚
20˚
20˚
20˚
45˚
45˚
20˚
20˚
20˚
20˚
20˚
20˚
20˚
20˚
20˚
45˚
45˚
NT-00462
NT-11
Note
NOTE
For sea transportation
CAUTION:
The eye bolts are exclusively used for towing and sea transportation tie-down, and do not use them
for ground and freight transportation.
(A)
Front tie-down hook
(C)
Chain pulling range at tie-down
condition
(E)
1,500 mm (59.1 in)
(B)
Eye bolt
(D)
400 mm (15.7 in)
(F)
1,217 mm (47.9 in)
(F)
(E)
(D)
:(C)
(A)
(B)
70˚
70˚
70˚
70˚
43˚
43˚
70˚
NT-00463
NT-12
Note
NOTE
• Vehicle sinking volume at tie-down condition
CAUTION:
The vehicle sinking volume at tie-down condition should be less than 50 mm (1.97 in) and make sure
to fix the vehicle securely.
Check to see if the tensions of chains or belts at tie-down condition are appropriate in the following
procedures.
1) Before tie-down, measure the distance between the highest tire point and highest arch point at the center
of wheel.
2) After tie-down, measure the distance between the highest tire point and highest arch point at the center of
wheel.
3) If the distance (A) between the measured value of 1) and 2) above, is less than 50 mm (1.97 in), it is judged
as OK. If the distance is 50 mm (1.97 in) or more, it is judged as NG because the tension is too high.
• Notes for the use of tie-down hook
When the vehicle is tied down from vehicle inside, hook the hooks of tie-down chain from vehicle inside, and
when the vehicle is tied down from vehicle outside, hook the hooks of tie-down chain from vehicle outside.
For front tie-down hook, use S hook and J hook, and for rear tie-down hole, use S hook, J hook and T hook.
T hook can be used only for rear tie-down hole.
(B)
Arch position before tie-down
(C)
Arch position after tie-down
(A)
(B)
(C)
(A)
(B)
(C)
NT-00456
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст