Subaru Tribeca (2014 year). Instruction — part 24
& Map light
1. Remove the lens by prying the edge of
the lens with a flat-head screwdriver.
2. Turn the bulb until the flat surfaces at
its ends are aligned vertically. Pull the bulb
straight downward to remove it.
3. Install a new bulb.
4. Reinstall the lens.
& Vanity mirror light
1. Remove the lens by prying the edge of
the lens with a flat-head screwdriver.
2. Pull the bulb out of the socket.
3. Install a new bulb.
4. Reinstall the lens.
& Door step light
It may be difficult to replace the bulbs.
Have the bulbs replaced by your SUBARU
dealer if necessary.
Maintenance and service
11-43
– CONTINUED –
11-44
Maintenance and service
& Cargo area light
1. Remove the cargo area light assembly
by prying the edge of the light with a flat-
head screwdriver.
2. Remove the lens from the cargo area
light assembly.
3. Pull the bulb out of the socket.
4. Install a new bulb.
5. Reinstall the lens to the cargo area
light assembly.
6. Reinstall the cargo area light assembly
to the roof trim.
Specifications . . . . . . . . . . . . . . 12-2
Dimensions. . . . . . . . . . . . . . ... 12-2
Engine . . . . . . . . . . . . . . . . .. 12-2
Fuel . . . . . . . . . . . . . . . . . .. 12-3
Engine oil . . . . . . . . . . . . . . . . 12-4
Front differential and rear differential gear oil. . . 12-6
Fluids . . . . . . . . . . . . . . . . ... 12-7
Engine coolant . . . . . . . . . . . . . .. 12-7
Electrical system. . . . . . . . . . . . ... 12-7
Tires. . . . . . . . . . . . . . . . . . 12-8
Fuses and circuits . . . . . . . . . . . . .12-9
Fuse panel located in the passenger
compartment . . . . . . . . . . . . . .. 12-9
Fuse panel located in the engine
compartment . . . . . . . . . . . . . .12-11
Bulb chart. . . . . . . . . . . . . . . .12-12
Vehicle identification . . . . . . . . . . ...12-15
Specifications
12
12-2
Specifications
Specifications
These specifications are subject to change without notice.
& Dimensions
in (mm)
Overall length
191.5 (4,865)
Overall width
73.9 (1,878)
Overall height
Without roof rail
66.7 (1,695)
With roof rail
68.1 (1,730)
Wheel base
108.1 (2,745)
Tread
Front
62.0 (1,575)
Rear
62.0 (1,575)
Ground clearance
8.3 (211)
& Engine
Engine model
EZ36D
(3.6 L, DOHC, non-turbo)
Engine type
Horizontally opposed, liquid cooled 6 cylinder, 4 stroke gasoline engine
Displacement cc (cu-in)
3,630 (221.5)
Bore 6 Stroke in (mm)
3.62 6 3.58 (92.0 6 91.0)
Compression ratio
10.5 : 1
Firing order
1 – 6 – 3 – 2 – 5 – 4
& Fuel
Fuel requirement
Fuel tank capacity
Unleaded gasoline with 87 AKI (90 RON) or higher
16.9 US gal (64 liters, 14.1 Imp gal)
For more details, refer to “Fuel” F7-2.
Specifications
12-3
– CONTINUED –
12-4
Specifications
& Engine oil
For the checking, adding and replacing procedure or other details, refer to “Engine oil” F11-7.
NOTE
The procedure for changing the engine oil and oil filter should be performed by a properly-trained expert. It is recommended
that you have this service performed by your SUBARU dealer.
! Approved engine oil
Always use the SUBARU approved engine oil. For further details, please contact your SUBARU dealer.
If the approved engine oil is unavailable, use the alternative engine oil described on the next page.
! Alternative engine oil
If the SUBARU approved oil is unavailable, the following alternative oil can be used.
NOTE
. Each quantity indicated is only a guideline. The necessary quantity for replacement may differ slightly depending on the
temperature and other factors.
. In choosing an oil, you want the proper quality and viscosity, as well as one that will enhance fuel economy. Oils of lower
viscosity provide better fuel economy. However, in hot weather, oil of higher viscosity is required to properly lubricate the
engine. The following table lists the recommended viscosities and applicable temperatures.
. When adding oil, different brands may be used together as long as they are the same API classification and SAE viscosity
as those recommended by SUBARU.
Oil grade
SAE viscosity No. and
applicable temperature
Engine oil capacity
API classification SM or SN with
the words
“ENERGY CONSERVING” or
“RESOURCE CONSERVING”
or
ILSAC GF-4 or GF-5, which can
be identified with the ILSAC
certification mark (Starburst
mark)
Your vehicle is designed to use 5W-30
conventional motor oil, however 5W-30
synthetic may be used for optimum
engine performance.
If you do choose to use synthetic oil,
we recommend that you continue using
synthetic for the life of your vehicle.
– Adding the oil from L to F level:
1.1 US qt (1.0 liter, 0.9 Imp qt)
– Changing the oil and oil filter:
6.9 US qt (6.5 liters, 5.7 Imp qt)
Specifications
12-5
– CONTINUED –
12-6
Specifications
& Front differential and rear differential gear oil
Oil grade
API classification GL-5
SAE viscosity No. and applicable
temperature
Oil capacity*
1
–
Remarks*
2
Front differential gear oil
1.5 US qt (1.4 liters, 1.2 Imp qt)
“Front differential gear oil” F11-15
Rear differential gear oil
0.8 US qt (0.8 liters, 0.7 Imp qt)
“Rear differential gear oil” F11-16
*1: The indicated oil quantity is only a guideline. The necessary quantity for replacement may differ slightly depending on the temperature and other
factors. After refilling the gearbox with oil, the oil level should be checked.
*2: For more details about maintenance and service, refer to the indicated section.
& Fluids
Fluid
Fluid type*
1
Fluid capacity*
2
Remarks*
3
Automatic transmission fluid · SUBARU ATF
· IDEMITSU ATF HP
10.4 US qt (9.8 liters, 8.6 Imp qt)
“Automatic transmission fluid” F11-
14
Power steering fluid
· SUBARU ATF
· IDEMITSU ATF HP
· “Dexron III” Type Automatic
Transmission Fluid
0.95 US qt (0.9 liters, 0.79 Imp qt)
· “Power steering” F7-18
· “Power steering fluid” F11-16
Brake fluid
FMVSS No. 116, fresh DOT 3 or DOT 4
brake fluid
–
“Brake fluid” F11-17
*1: Use one of the indicated types of fluid.
*2: The indicated fluid quantity is only a guideline. The necessary quantity for replacement may differ slightly depending on the temperature and other
factors.
*3: For more details about maintenance and service, refer to the indicated section.
& Engine coolant
Coolant type
Coolant capacity
SUBARU Super Coolant
8.0 US qt (7.6 liters, 6.7 Imp qt)
The indicated coolant quantity is only a guideline. The necessary quantity for replacement may differ slightly depending on the temperature and other
factors. For more details about maintenance and service, refer to “Cooling system” F11-10.
& Electrical system
Battery type and capacity (5HR)
75D23L (12V-52AH)
Alternator
12V-130A
Spark plugs
SILFR6C11 (NGK)
Specifications
12-7
– CONTINUED –
12-8
Specifications
& Tires
Tire size
P255/55R18 104H
255/55R18 105H
Wheel size
18 6 8JJ
Pressure
Front
33 psi (230 kPa, 2.3 kgf/cm
2
)
Rear
32 psi (220 kPa, 2.2 kgf/cm
2
)
Temporary spare tire
Size
T165/80R17
Pressure
60 psi (420 kPa, 4.2 kgf/cm
2
)
Wheel nut tightening torque
Aluminum wheels (silver-colored)
89 lbf·ft (120 N·m, 12 kgf·m)
*1*3
Chrome-finished wheels
111 lbf·ft (150 N·m, 15 kgf·m)
*2*3
Temporary spare tire wheel
89 lbf·ft (120 N·m, 12 kgf·m)
*1*3
*1: This torque is equivalent to applying the following load at the end of the wheel nut wrench.
When you use a wheel nut wrench of the 10.8-inch (275 mm) length: Approximately 96 to 115 lbf (43 to 52 kgf)
When you use a wheel nut wrench of the 13.2-inch (335 mm) length: Approximately 73 to 87 lbf (33 to 40 kgf)
If you have tightened the wheel nuts by yourself, have the tightening torque checked at the nearest automotive service facility as soon as possible.
*2: This torque is equivalent to applying approximately 87 to 109 lbf (40 to 49 kgf) at the end of the wheel nut wrench with a length of 13.2 inches (335
mm). If you have tightened the wheel nuts by yourself, have the tightening torque checked at the nearest automotive service facility as soon as possible.
*3: For information about the length of the wheel nut wrench and the wheel nut tightening procedure, refer to “Changing a flat tire” F9-6.
Fuses and circuits
& Fuse panel located in the passenger compartment
Fuse
panel
Fuse
rating
Circuit
1
20A
.
Trailer hitch connector
2
Empty
3
15A
.
Door locking
4
7.5A
.
Front wiper deicer relay
.
Moonroof
5
7.5A
.
Combination meter
6
7.5A
.
Remote
control
rear
view mirrors
.
Seat heater relay
7
15A
.
Combination meter
.
Integrated unit
8
15A
.
Stop light
9
20A
.
Mirror heater
.
Front wiper deicer
10
7.5A
.
Power supply (battery)
11
7.5A
.
Turn signal unit
12
15A
.
Automatic transmission
unit
.
SRS
airbag
system
(sub)
.
Engine control unit
.
Integrated unit
Specifications
12-9
– CONTINUED –
12-10
Specifications
Fuse
panel
Fuse
rating
Circuit
13
20A
.
Cargo socket
14
15A
.
Parking light
.
Tail light
.
Rear combination light
15
Empty
16
10A
.
Illumination
17
15A
.
Seat heaters
18
10A
.
Backup light
19
7.5A
.
Headlight right side re-
lay
20
Empty
21
7.5A
.
Starter relay
22
15A
.
Air conditioner
.
Rear window defogger
relay coil
23
15A
.
Rear wiper
.
Rear window washer
24
15A
.
Audio unit
25
15A
.
SRS
airbag
system
(main)
26
7.5A
.
Power window relay
27
15A
.
Rear blower fan
Fuse
panel
Fuse
rating
Circuit
28
15A
.
Rear blower fan
29
15A
.
Fog light
30
30A
.
Front wiper
31
7.5A
.
Auto air conditioner unit
.
Integrated unit
32
7.5A
.
Headlight left side relay
33
7.5A
.
Vehicle Dynamics Con-
trol unit
& Fuse panel located in the engine compartment
Fuse
panel
Fuse
rating
Circuit
1
30A
.
Vehicle Dynamics Con-
trol unit
2
25A
.
Main fan (cooling fan)
3
25A
.
Main fan (cooling fan)
4
20A
.
Console socket
5
15A
.
Headlight (right side)
6
15A
.
Headlight (left side)
7
20A
.
Back-up
8
15A
.
Horn
9
25A
.
Rear window defogger
10
15A
.
Fuel pump
11
15A
.
Automatic
transmission
control unit
12
7.5A
.
Engine control unit
13
15A
.
Turn and hazard warning
flasher
14
20A
.
Parking switch
15
7.5A
.
Alternator
Specifications
12-11
12-12
Specifications
Bulb chart
NOTE
Lights A and B are the LED (Light Emitting Diode) type. Consult your SUBARU dealer for replacement.
Wattage
Bulb No.
1)
High beam headlight
12V-60W
HB3
2)
Low beam headlight
Models with HID light
12V-35W
D1S
Models with halogen light
12V-55W
H7
3)
Front turn signal/Parking light
12V-28/8W
2357NA
4)
Parking/Front side marker light
12V-5W
168(W5W)
5)
Map light
12V-8W
–
6)
Dome light
Models with Rear Seat Entertainment
12V-5W
–
Models without Rear Seat Entertainment
12V-8W
–
7)
Door step light
12V-3W
–
8)
Vanity mirror light
12V-3W
9)
Fog light
12V-55W
H3
10)
Cargo area light
12V-13W
912
11)
Tail light
12V-5W
168(W5W)
12)
Stop light/Tail light
12V-27/8W
1157(W27/8W)
13)
Rear turn signal light
12V-27W
1156(W27W)
14)
Backup light
12V-16W
921(W16W)
15)
Rear gate light
12V-5W
(W5W)
16)
License plate light
12V-5W
168(W5W)
A)
Side turn signal light
–
–
B)
High-mounted stop light
–
–
WARNING
. Bulbs may become very hot while
illuminated. Before replacing
bulbs, turn off the bulbs and wait
until the bulbs cool down. Other-
wise, there is a risk of sustaining
a burn injury.
. For models with HID low beam
headlights, observe the following
precautions. Not doing so carries
the risk of an electric shock that
could result in serious injury
because the HID bulbs use an
extremely high voltage.
– Do not replace any headlight
bulbs (both low beam and
high beam) by yourself.
– Do not remove/restore the
headlight assemblies by your-
self.
– Do not remove any headlight-
assembly components by
yourself.
For replacement, contact your
SUBARU dealer.
Specifications
12-13
– CONTINUED –
Vehicle identification
1)
Vehicle identification number
2)
Certification and bar code label
3)
Tire inflation pressure label
4)
Vehicle identification number plate
5)
Model number label
6)
Emission control label
7)
Fuel label
8)
Air conditioner label
Specifications
12-15
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст