Suzuki Grand Vitara JB627. Service manual — part 148
3B-34 Differential: Rear
23) Upon completion of gear tooth contact check in Step
22), caulk flange nut (2) with caulking tool (1) and
hammer.
24) Clean mating surface of differential carrier (2) and
rear cover (1), apply sealant to carrier as shown in
figure by such amount that its section is 1.5 mm
(0.059 in.) in diameter, mate rear cover with
differential carrier, and then tighten bolts to specified
torque.
“A”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)
Tightening torque
Rear cover bolt No.1 (a): 50 N·m (5.0 kgf-m, 17.0
lb-ft)
Rear cover bolt No.2 (b): 60 N·m (6.0 kgf-m, 43.5
lb-ft)
25) Assembly rear drive right retainer as follows.
a) Install rear drive shaft bearing (1) using special
tool and press (2).
Special tool
(A): 09913–75520
b) Install snap ring.
c) Install oil seal using special tools as shown in
figure.
Distance between retainer surface and oil
seal
“a”: 2.5 – 3.0 mm (0.10 – 0.12 in.)
Special tool
(A): 09924–74510
(B): 09951–16090
I1JA01322021-01
(a)
1
2
(b)
2, “A”
I6JB01321001-03
2
(A)
1
I5JB0A322012-01
I5JB0A322010-01
I5JB0A322013-02
Differential: Rear 3B-35
26) Assembly rear drive left retainer in the same manner
at Step 25) in this assembly procedure.
27) Clean mating surface of right retainer, carrier (1) and
rear cover (2), apply sealant to carrier and rear cover
as shown in figure by such amount that its section is
1.5 mm (0.059 in.) in diameter, mate right retainer
with carrier and rear cover, and then tighten bolts to
specified torque.
“A”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)
Tightening torque
Retainer bolt: 50 N·m (5.0 kgf-m, 36.5 lb-ft)
28) Clean mating surface of left retainer, carrier (1) and
rear cover (2), apply sealant to carrier and rear cover
as shown in figure by such amount that its section is
1.5 mm (0.059 in.) in diameter, mate left retainer with
carrier and rear cover, and then tighten bolts to
specified torque.
“A”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)
Tightening torque
Retainer bolt: 50 N·m (5.0 kgf-m, 36.5 lb-ft)
29) Install rear drive right and left shaft using plastic
hammer.
Rear Differential Inspection
S6JB0B3226006
Refer to “Front Differential Inspection: Front”.
1
“A”
2
I5JB0A321048-01
“A”
2
1
I5JB0A322014-01
3B-36 Differential: Rear
Specifications
Tightening Torque Specifications
S6JB0B3227001
NOTE
The specified tightening torque is also described in the following.
“Rear Differential Unit Components: Rear”
“Rear Differential Components: Rear”
Reference:
For the tightening torque of fastener not specified in this section, refer to “Fastener Information in Section 0A”.
Special Tools and Equipment
Recommended Service Material
S6JB0B3228001
NOTE
Required service material is also described in the following.
“Rear Differential Components: Rear”
Special Tool
S6JB0B3228002
Fastening part
Tightening torque
Note
N
⋅m
kgf-m
lb-ft
Rear differential front mounting bolt
120
12.0
87.0
Rear differential rear mounting bolt
120
12.0
87.0
Bevel gear bolt
Tighten 40 N
⋅m (4.0 kgf-m, 29.5 lb-ft) + 50° )
Rear cover bolt No.1
50
5.0
17.0
Rear cover bolt No.2
60
6.0
43.5
Retainer bolt
50
5.0
36.5
Material
SUZUKI recommended product or Specification
Note
Grease
SUZUKI Super Grease A
P/No.: 99000–25010
Sealant
SUZUKI Bond No.1217G
P/No.: 99000–31260
Thread lock cement
Thread Lock Cement Super 1322
P/No.: 99000–32110
09900–20607
09900–20701
Dial gauge
Magnetic stand
09913–50121
09913–65135
Oil seal remover
Bearing puller
09913–75510
09913–75520
Bearing installer
Bearing installer
Differential: Rear 3B-37
09913–75821
09913–85210
Bearing installer attachment
Bearing installer
09922–66021
09922–75222
Flange holder
Differential gear preload
adjuster
09922–76520
09924–74510
Bevel pinion gauge block
Bearing and oil seal handle
09924–84510–004
09924–84510–005
Bearing installer attachment
Bearing installer attachment
(D)
09925–14520
09925–86010
Bearing and oil seal installer
(80 x 50 mm)
Bearing puller attachment
09925–88210
09926–78311
Bearing puller attachment
Differential bevel pinion
dummy
09926–78311–002
09926–78320
Pinion mounting dummy
Mounting dummy
09928–06510
09930–30104
Differential torque checking
tool
Sliding shaft
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст