Infiniti G20 (P11). Manual — part 86
SAT204D
8.
Install drive plates, driven plates, retaining plate and dish plate
for overrun clutch.
9.
Install snap ring for overrun clutch.
SAT227D
10. Measure clearance between overrun clutch retaining plate and
snap ring.
If not within allowable limit, select proper retaining plate.
Specified clearance:
Standard: 1.0 - 1.4 mm (0.039 - 0.055 in)
Allowable limit: 2.0 mm (0.079 in)
Overrun clutch retaining plate:
Refer to SDS, AT-391.
SAT203D
11. Install drive plates, driven plates, retaining plate and dish plate
for forward clutch.
Take care with the order and direction of plates.
12. Install snap ring for forward clutch.
SAT228D
13. Measure clearance between forward clutch retaining plate and
snap ring.
If not within allowable limit, select proper retaining plate.
Specified clearance:
Standard: 0.45 - 0.85 mm (0.0177 - 0.0335 in)
Allowable limit: 1.85 mm (0.0728 in)
Forward clutch retaining plate:
Refer to SDS, AT-391.
SAT201D
14. Check operation of forward clutch.
Refer to “Forward Clutch and Overrun Clutch”, AT-336.
GI
MA
EM
LC
EC
FE
CL
MT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REPAIR FOR COMPONENT PARTS
Forward Clutch and Overrun Clutch (Cont’d)
AT-341
SAT202D
15. Check operation of overrun clutch.
Refer to “Forward Clutch and Overrun Clutch”, AT-336.
REPAIR FOR COMPONENT PARTS
Forward Clutch and Overrun Clutch (Cont’d)
AT-342
Low & Reverse Brake
COMPONENTS
=NCAT0153
SAT486JA
SAT230D
DISASSEMBLY
NCAT0154
1.
Check operation of low & reverse brake.
a.
Apply compressed air to oil hole of transmission case.
b.
Check to see that retaining plate moves to snap ring.
c.
If retaining plate does not contact snap ring:
I
D-ring might be damaged.
I
Oil seal might be damaged.
I
Fluid might be leaking past piston check ball.
SAT231D
2.
Stand transmission case.
3.
Remove snap ring.
4.
Remove drive plates, driven plates, retaining plate from trans-
mission case.
AAT687
5.
Set Tool on spring retainer and remove snap ring while com-
pressing return springs.
I
Set Tool directly above return springs.
I
Do not expand snap ring excessively.
6.
Remove spring retainer and return springs.
GI
MA
EM
LC
EC
FE
CL
MT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REPAIR FOR COMPONENT PARTS
Low & Reverse Brake
AT-343
SAT303E
I
Do not remove return springs from spring retainer.
SAT234D
7.
Apply compressed air to oil hole of transmission case while
holding piston.
8.
Remove piston from transmission case by turning it.
SAT767G
9.
Remove D-ring and oil seal from piston.
INSPECTION
NCAT0155
Low & Reverse Clutch Snap Ring, Spring Retainer and
Return Springs
NCAT0155S01
I
Check for deformation, fatigue or damage.
I
Replace if necessary.
I
When replacing spring retainer and return springs,
replace them as a set.
REPAIR FOR COMPONENT PARTS
Low & Reverse Brake (Cont’d)
AT-344
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст