Infiniti G20 (P11). Manual — part 105
SFA800
Transaxle Side
NCAX0019S03
(DS83 type)
NCAX0019S0301
1.
Install boot and new small boot band on drive shaft.
Cover drive shaft serration with tape so as not to damage boot
during installation.
SFA514A
2.
Install ball cage, inner race and balls as a unit, making sure the
marks which were made during disassembly are properly
aligned.
3.
Install new snap ring.
SFA149A
4.
Pack drive shaft with specified amount of grease.
Specified amount of grease:
115 - 135 g (4.06 - 4.76 oz)
5.
Install slide joint housing, then install new snap ring.
6.
Make sure that boot is properly installed on the drive shaft
groove.
Set boot so that it does not swell and deform when its length
is “L
2
”.
Length “L
2
”:
98 mm (3.86 in)
SFA395
7.
Lock new larger and smaller boot bands securely with a suit-
able tool.
SFA800
(TS83 type)
NCAX0019S0302
1.
Install boot and new small boot band on drive shaft.
Cover drive shaft serration with tape to prevent damage to
boot during installation.
GI
MA
EM
LC
EC
FE
CL
MT
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FRONT AXLE
Drive Shaft (Cont’d)
AX-17
SFA023A
2.
Install spider assembly securely, making sure the marks which
were made during disassembly are properly aligned.
3.
Install new snap ring.
SFA993
4.
Pack drive shaft with specified amount of grease.
Specified amount of grease:
125 - 145 g (4.41 - 5.11 oz)
5.
Install slide joint housing.
6.
Set boot so that it does not swell and deform when its length
is “L
2
”.
Length “L
2
”:
99 mm (3.90 in)
Make sure that boot is properly installed on the drive shaft
groove.
SFA395
7.
Lock new larger and smaller boot bands securely with a suit-
able tool.
SFA618
Support Bearing
NCAX0019S04
I
Press bearing into retainer.
SFA694
I
Press drive shaft into bearing.
FRONT AXLE
Drive Shaft (Cont’d)
AX-18
SFA444B
I
Install snap ring.
I
Install new dust shield.
Service Data and Specifications (SDS)
DRIVE SHAFT
NCAX0020
Applied model
RH
LH
Both
With viscous type
Without viscous type
Joint type
Transaxle side
DS83
TS83
Wheel side
BF86
Grease
Quality
Nissan genuine grease or equivalent
Capacity
g (oz)
Transaxle side
115 - 135 (4.06 - 4.76)
125 - 145 (4.41 - 5.11)
Wheel side
95 - 115 (3.35 - 4.06)
Boot length
mm (in)
Transaxle side “L
2
”
98 (3.86)
99 (3.90)
Wheel side “L
1
”
100.5 (3.96)
SFA961AB
SFA962A
WHEEL BEARING (FRONT)
NCAX0021
Wheel bearing axial end play limit
mm (in)
0.05 (0.0020) or less
Wheel bearing lock nut tightening torque
N·m (kg-m, ft-lb)
235 - 314 (24 - 32, 174 - 231)
GI
MA
EM
LC
EC
FE
CL
MT
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FRONT AXLE
Drive Shaft (Cont’d)
AX-19
SBR820B
Precautions
PRECAUTIONS
NCAX0022
I
When installing each rubber part, final tightening must be
carried out under unladen condition* with tires on ground.
*: Fuel, radiator coolant and engine oil full. Spare tire, jack,
hand tools and mats in designated positions.
I
Use flare nut wrench when removing or installing brake
tubes.
I
After installing removed suspension parts, check wheel
alignment.
I
Do not jack up at the trailing arm and lateral link.
I
Always torque brake lines when installing.
Preparation
COMMERCIAL SERVICE TOOLS
NCAX0024
Tool name
Description
GG94310000
1 Flare nut crowfoot
2 Torque wrench
NT360
Removing and installing brake piping
a: 10 mm (0.39 in)
Noise, Vibration and Harshness (NVH)
Troubleshooting
NCAX0025
Refer to “Noise, Vibration and Harshness (NVH) Troubleshooting”,
“FRONT AXLE”, AX-3.
SMA525A
On-vehicle Service
REAR AXLE PARTS
NCAX0026
Check axle and suspension parts for excessive play, wear or dam-
age.
I
Shake each rear wheel to check for excessive play.
REAR AXLE
Precautions
AX-20
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст