Infiniti G20 (P11). Manual — part 277
![](/vehicles/zatt/wheiso/zix/mel.png)
DTC Confirmation Procedure
NCEC0593
NOTE:
If “DTC Confirmation Procedure” has been previously conducted,
always turn ignition switch “OFF” and wait at least 10 seconds
before conducting the next test.
TESTING CONDITION:
Always perform test at a temperature of 5°C (41°F) or more.
SEF205Y
SEF206Y
SEF237Y
WITH CONSULT-II
NCEC0593S01
1)
Start engine and warm it up to normal operating temperature.
2)
Turn ignition switch “OFF” and wait at least 10 seconds.
3)
Turn ignition switch “ON”.
4)
Select “PURG VOL CN/V P1444” of “EVAPORATIVE SYS-
TEM” in “DTC WORK SUPPORT” mode with CONSULT-II.
5)
Touch “START”.
6)
Start engine and let it idle until “TESTING” on CONSULT-II
changes to “COMPLETED”. (It will take for approximately 10
seconds.)
If “TESTING” is not displayed after 5 minutes, retry from
step 2.
7)
Make sure that “OK” is displayed after touching “SELF-DIAG
RESULTS”.
If
“NG”
is
displayed,
refer
to
“Diagnostic
Procedure”, EC-521.
WITH GST
NCEC0593S02
1)
Start engine and warm it up to normal operating temperature.
2)
Turn ignition switch “OFF” and wait at least 10 seconds.
3)
Start engine and let it idle for at least 20 seconds.
4)
Select “MODE 7” with GST.
5)
If 1st trip DTC is detected, go to “Diagnostic Procedure”,
EC-521.
GI
MA
EM
LC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P1444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
DTC Confirmation Procedure
EC-519
![](/vehicles/zatt/wheiso/zix/thang.png)
Wiring Diagram
NCEC0594
TEC711
DTC P1444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Wiring Diagram
EC-520
![](/vehicles/zatt/wheiso/zix/veverit.png)
Diagnostic Procedure
NCEC0595
1
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
1. Turn ignition switch “OFF”.
2. Disconnect EVAP canister purge volume control solenoid valve harness connector.
SEF851X
3. Turn ignition switch “ON”.
4. Check voltage between EVAP canister purge volume control solenoid valve terminal 1 and engine ground with CON-
SULT-II or tester.
SEF948X
OK or NG
OK
©
GO TO 3.
NG
©
GO TO 2.
2
DETECT MALFUNCTIONING PART
Check the following.
I
Harness connectors M62, F24
I
Harness connectors F13, F51
I
Fuse block (J/B) connector M2
I
10A fuse
I
Harness for open or short between EVAP canister purge volume control solenoid valve and fuse
©
Repair harness or connectors.
3
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OUTPUT SIGNAL CIRCUIT
FOR OPEN AND SHORT
1. Turn ignition switch “OFF”.
2. Disconnect ECM harness connector.
3. Check harness continuity between ECM terminal 14 and EVAP canister purge volume control solenoid valve terminal 2.
Refer to Wiring Diagram.
Continuity should exist.
4. Also check harness for short to ground and short to power.
OK or NG
OK
©
GO TO 5.
NG
©
GO TO 4.
GI
MA
EM
LC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P1444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Diagnostic Procedure
EC-521
![](/vehicles/zatt/wheiso/zix/par.png)
4
DETECT MALFUNCTIONING PART
Check the following.
I
Harness connectors F13, F51
I
Harness for open or short between EVAP canister purge volume control solenoid valve and ECM
©
Repair open circuit or short to ground or short to power in harness or connectors.
5
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR HOSE
Check disconnection or improper connection of hose connected to EVAP control system pressure sensor.
SEF860X
OK or NG
OK
©
GO TO 6.
NG
©
Repair it.
6
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR
1. Disconnect EVAP control system pressure sensor harness connector.
2. Check connectors for water.
Water should not exist.
OK or NG
OK
©
GO TO 7.
NG
©
Replace EVAP control system pressure sensor.
DTC P1444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Diagnostic Procedure (Cont’d)
EC-522
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст