Infiniti QX56 (JA60). Manual — part 303
SIDE OIL SEAL
DLN-135
< ON-VEHICLE REPAIR >
[ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SIDE OIL SEAL
Removal and Installation
INFOID:0000000005148890
REMOVAL
1. Remove the front propeller shaft. Refer to
DLN-186, "Removal and Installation"
.
2. Remove the companion flange. Refer to
DLN-142, "Disassembly and Assembly"
.
3. Remove the transfer control device from the transfer assembly. Refer to
DLN-136, "Removal and Installa-
4. Remove the side oil seal using suitable tool.
CAUTION:
Do not damage shift cross.
INSTALLATION
1. Install the new side oil seal until it is flush with the end face of
case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2. Install the transfer control device to the transfer assembly. Refer
DLN-136, "Removal and Installation"
3. Install the companion flange. Refer to
.
4. Install the front propeller shaft. Refer to
DLN-186, "Removal and Installation"
SDIA2666E
Tool number
: ST22360002 (J-25679-01)
SDIA2665E
DLN-136
< ON-VEHICLE REPAIR >
[ATX14B]
TRANSFER CONTROL DEVICE
TRANSFER CONTROL DEVICE
Removal and Installation
INFOID:0000000005380646
REMOVAL
CAUTION:
Change vehicle state to AUTO, and then remove and install transfer control device.
1. Remove front propeller shaft. Refer to
DLN-186, "Removal and Installation"
.
2. Disconnect the transfer control device connector.
3. Remove transfer control lever.
4. Disconnect vacuum line.
5. Remove transfer control device.
INSTALLATION
CAUTION:
Check 4WD shift indicator after installation. Refer to
DLN-121, "Precaution for Transfer Assembly and
Transfer Control Unit Replacement"
Installation is in the reverse order of removal.
1.
Shift lever
2.
Actuator
SDIA2654E
AIR BREATHER HOSE
DLN-137
< ON-VEHICLE REPAIR >
[ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000005148892
REMOVAL
INSTALLATION
CAUTION:
Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
1. Install each air breather hose into the breather tube (4). Set
each air breather hose with paint mark facing upward.
• A/T breather hose (1)
• Transfer breather hose (2)
• Actuator/transfer motor breather hose (3)
• Paint marks (A)
2. Install actuator/transfer motor air breather hose (1) and transfer
air breather hose (2) on clip (A) with the paint mark (B) facing
upward.
•
:Front
AWDIA0010ZZ
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Actuator
7.
Air breather hose clamp
8.
Clip E
9.
Transfer motor
10. Breather tube (transfer)
Vehicle front
ALDIA0110ZZ
ALDIA0111ZZ
DLN-138
< ON-VEHICLE REPAIR >
[ATX14B]
AIR BREATHER HOSE
3. Install clip (B) on actuator/transfer motor air breather hose (1)
and transfer air breather hose (2) with the paint mark (A)
matched.
•
:Front
4. Install actuator/transfer motor air breather hose (1) and transfer
air breather hose (2) on clip (B) and clip (C) with the paint mark
(A) and (D) facing upward.
•
:Front
5. Install the actuator air breather hose into the actuator (case con-
nector) until the hose end reaches the base of the tube. Set
actuator air breather hose with paint mark facing leftward.
6. Install clip (B) on transfer motor air breather hose (2) and trans-
fer air breather hose (1) with the paint mark (A) matched.
•
:Front
7. Install the transfer air breather hose into the breather tube
(transfer, metal connector) until the hose end reaches the base
of the tube. Set transfer air breather hose with paint mark facing
upwards.
AWDIA0011ZZ
AWDIA0012ZZ
SDIA3226E
AWDIA0013ZZ
SDIA3196E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст