Infiniti QX56 (JA60). Manual — part 915
![](/vehicles/zatt/vend/genn/bound.png)
TILT SYSTEM
ST-19
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
TILT SYSTEM
Removal and Installation
INFOID:0000000005147871
TILT MOTOR AND TILT SENSOR
Removal
1. Remove the lower driver instrument panel. Refer to
.
2. Disconnect the sonar switch.
3. Disconnect adjustable pedal switch.
4. Remove steering column cover
5. Disconnect the tilt sensor electrical connector.
6. Remove knee protector.
7. Remove the two tilt sensor screws and the tilt sensor.
8. Disconnect the tilt motor electrical connector.
9. Remove the tilt motor bolt and the tilt motor.
Installation
Installation is in reverse order of removal.
NOTE:
Make sure the tab in the tilt sensor is engaged in the bracket on the tilt motor.
AWGIA0086GB
1.
Tilt sensor
2.
Tilt motor
LGIA0026E
![](/vehicles/zatt/vend/genn/fead.png)
ST-20
< REMOVAL AND INSTALLATION >
STEERING COLUMN
STEERING COLUMN
Removal and Installation
INFOID:0000000005147872
CAUTION:
• Any time the ignition switch has been disconnecter, removed or installed, the keys must be re-rege-
stered in the BCM. Refer toConsult-III operations IVIS/NVIS.
• Do not exert any load or impact in the axial direction immediately before or after column removal.
• Do not to move steering gear during removal of steering column assembly.
REMOVAL
1. Remove combination switch and spiral cable from steering column assembly. Refer to
2. Remove the tilt motor and tilt sensor. Refer to
ST-19, "Removal and Installation"
3. Remove steering column cover. Refer to
ST-20, "Removal and Installation"
1.
Driver air bag module
2.
Steering wheel
3.
Steering wheel side cover
4.
Combination switch and spiral cable 5.
Steering column assembly
6.
Collar
7.
Hole cover seal
8.
Clamp
9.
Hole cover plate
10. Hole cover
11. Upper joint
12. Upper shaft
13. Boot clamp
14. Lower joint shaft
15. Boot and clips (plastic)
A.
Refer to
SR-5, "Removal and Installation"
AWGIA0113GB
![](/vehicles/zatt/vend/genn/uet.png)
STEERING COLUMN
ST-21
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
4. Remove lock nut and bolt, then separate upper shaft from upper
joint.
5. Remove two nuts and two bolts, then remove steering column
assembly from steering member.
6. Remove hole cover seal and clamp.
7. Remove nuts, then remove hole cover from dash panel.
8. Raise vehicle, then remove bolt (lower side) of lower joint shaft
and remove lower joint shaft and upper shaft as an assembly.
INSPECTION AFTER REMOVAL
• Check for damage to steering column jacket tube. If damage is found, replace steering column with new
one.
• If vehicle has been in a collision, check column length (L), (L
1
) and (L
2
) as shown. If out of specification,
replace steering column with new one.
LGIA0027E
LGIA0028E
LGIA0029E
Steering column length
(L)
: Refer to
(L
1
)
: Refer to
(L
2
)
: Refer to
WGIA0080E
![](/vehicles/zatt/vend/genn/wrammeld.png)
ST-22
< REMOVAL AND INSTALLATION >
STEERING COLUMN
• Check for proper lubrication, apply grease as necessary.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When installing the steering column, finger-tighten all of the lower bracket and joint retaining bolts;
then tighten them to specification. Do not apply undue stress to the steering column.
• The lower nut on the upper joint may not be reused.
NOTE:
• After installation, turn steering wheel to make sure it moves smoothly. Make sure the number of turns are the
same from the straight-forward position to left and right locks. Make sure that the steering wheel is in a neu-
tral position when driving straight ahead.
• When installing steering column to steering member, install nut from front side of vehicle.
INSPECTION AFTER INSTALLATION
• After installing steering column to vehicle, check tilt device operation range is within specification.
• Check if steering wheel operation can turn to the end of the left and
right stops smoothly.
SGIA0475E
Range "A"
: Refer to
WGIA0083E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст