Infiniti QX56 (JA60). Manual — part 966
TM-166
< ON-VEHICLE REPAIR >
AIR BREATHER HOSE
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000005402587
REMOVAL and INSTALLATION
2WD
CAUTION:
• Install air breather hose with paint mark at upper side.
• When installing the air breather hose, do not crush or block by folding or bending the hose.
• When inserting the hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend portion.
• Make sure clip is securely installed to bracket.
REMOVAL
AWDIA0554GB
A.
Set air breather hose with
paint mark at upper side
B.
Clip (set securely to bracket)
AIR BREATHER HOSE
TM-167
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4WD
INSTALLATION
CAUTION:
Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
1. Install each air breather hose into the breather tube (4). Set
each air breather hose with paint mark facing upward.
• A/T breather hose (1)
• Transfer breather hose (2)
• Actuator/transfer motor breather hose (3)
• Paint marks (A)
2. Install actuator/transfer motor air breather hose (1) and transfer
air breather hose (2) on clip (A) with the paint mark (B) facing
upward.
•
:Front
AWDIA0010ZZ
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Actuator
7.
Air breather hose clamp
8.
Clip E
9.
Transfer motor
10. Breather tube (transfer)
Vehicle front
ALDIA0110ZZ
ALDIA0111ZZ
TM-168
< ON-VEHICLE REPAIR >
AIR BREATHER HOSE
3. Install clip (B) on actuator/transfer motor air breather hose (1)
and transfer air breather hose (2) with the paint mark (A)
matched.
•
:Front
4. Install actuator/transfer motor air breather hose (1) and transfer
air breather hose (2) on clip (B) and clip (C) with the paint mark
(A) and (D) facing upward.
•
:Front
5. Install the actuator air breather hose into the actuator (case con-
nector) until the hose end reaches the base of the tube. Set
actuator air breather hose with paint mark facing leftward.
6. Install clip (B) on transfer motor air breather hose (2) and trans-
fer air breather hose (1) with the paint mark (A) matched.
•
:Front
7. Install the transfer air breather hose into the breather tube
(transfer, metal connector) until the hose end reaches the base
of the tube. Set transfer air breather hose with paint mark facing
upwards.
AWDIA0011ZZ
AWDIA0012ZZ
SDIA3226E
AWDIA0013ZZ
SDIA3196E
AIR BREATHER HOSE
TM-169
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
8. Install the transfer motor air breather hose into the transfer
motor (case connector) until the hose end reaches the end of
the curved section. Set transfer motor air breather hose with
paint mark facing leftward.
SDIA3194E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст