Infiniti QX56 (JA60). Manual — part 831
FRONT SEAT
SE-49
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1.
Headrest
2.
Headrest holder with multi-position
lock
3.
Seatback assembly
4.
Lumbar switch bezel
5.
Power seat switch escutcheon
6.
Recliner switch knob
7.
Slide switch knob
8.
Driver power seat frame assembly
9.
Inner leg cover
10. Driver seat wiring harness
11. Bolt cover
12. Seat cushion outer finisher
13. Outer pedestal finisher
14. Seat cushion front finisher
15. Seat cushion inner finisher
16. Seat cushion frame
17. Seat cushion heating element
18. Seat cushion pad
19. Seat cushion trim cover
20. Armrest assembly
21. Headrest holder
22. Seat slide/ recline switch
23. Power lumbar switch
SE-50
< ON-VEHICLE REPAIR >
FRONT SEAT
Passenger Seat
WIIA0476E
1.
Headrest
2.
Headrest holder with multi-position
lock
3.
Seatback board
4.
Armrest assembly
5.
Lumbar switch bezel
6.
Fold flat link bar
7.
Outboard reclining arm outer cover
8.
Outboard reclining arm inner cover
9.
Inboard reclining arm inner cover
10. Latch cover
11. Inner leg cover
12. Outboard reclining arm inner cover
13. Seat cushion inner cover
14. Passenger seat wiring harness
15. Inner front leg cover
16. Power seat frame assembly
17. NVH assembly
18. Seat cushion front finisher
FRONT SEAT
SE-51
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Removal and Installation
INFOID:0000000005147410
REMOVAL
CAUTION:
• When removing or installing the seat trim, handle it carefully to keep dirt out and avoid damage.
• Before removing the front seat, turn the ignition switch off, disconnect both battery cables and wait
at least 3 minutes.
• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-
tor with the side air bag module connector. Such an error may cause the air bag to deploy.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After front side air bag module inflates, front seatback assembly must be replaced.
• Front passenger seat is equipped with an Occupant Classification System sensor and control mod-
ule. Do not disassemble front passenger seat cushion assembly or remove the trim as this will affect
the Occupant Classification System calibration.
• Always replace passenger seat cushion as an assembly.
1. Slide the seat until the four body mounting bolts are visible and a tool can be inserted.
NOTE:
• If disassembling the seat after removal, set the front/rear cushion lifters to the top position.
2. Disconnect both battery cables and wait at least 3 minutes.
3. Remove the outer pedestal finisher.
4. Disconnect the side air bag module harness connector.
5. Remove the four body mounting bolts.
6. Disconnect the power seat harness connectors and remove the seat from the vehicle.
CAUTION:
When removing and installing the seat, use shop cloths to protect the vehicle from damage.
INSTALLATION
Installation is in the reverse order of removal.
19. Outer pedestal finisher
20. Seat cushion outer finisher
21. Seat cushion assembly
22. Power seat switch escutcheon
23. Slide switch knob
24. Recliner switch knob
25. Seatback assembly
26. Headrest holder
27. Seat slide/ recline switch
28. Power lumbar switch
SE-52
< ON-VEHICLE REPAIR >
SECOND SEAT
SECOND SEAT
Exploded View
INFOID:0000000005147411
Second Row RH
WIIA1013E
1.
Headrest
2.
Seatback pad
3.
Seatback frame
4.
Rear seat bezel
5.
RH Headrest guide (free)
6.
LH Headrest guide (locking)
7.
Seat back panel
8.
Seat actuator assembly
9.
Reclining device inner cover
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст