Infiniti G35 (V35) Sedan. Manual — part 697
![](/vehicles/zatt/tenge/utoanga/urche.png)
EXT-26
< ON-VEHICLE REPAIR >
FLOOR SIDE FAIRING
FLOOR SIDE FAIRING
Exploded View
INFOID:0000000000961806
Removal and Installation
INFOID:0000000000961807
REMOVAL
ENGINE LOWER COVER
1.
Remove engine lower cover mounting clip.
2.
Remove engine lower cover mounting bolts with power tool.
3.
Remove front under cover.
FLOOR UNDER COVER (LH/RH)
1.
Remove floor under cover mounting clips.
2.
Remove floor under cover mounting bolts and nuts with power tool.
3.
Remove floor under cover.
REAR DIFFUSER
1.
Remove rear diffuser mounting clips.
2.
Remove rear diffuser mounting bolts and nuts with power tool.
3.
Remove rear diffuser.
INSTALLATION
1.
Engine lower cover
2.
Front under cover (4WD models) 3.
Floor under cover (RH)
4.
Floor under cover (LH)
5.
Rear diffuser bracket
6.
Rear diffuser
7.
Front under cover (2WD models)
JMKIA0081GB
FLOOR SIDE FAIRING
EXT-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Install in the reverse order of removal.
![](/vehicles/zatt/tenge/utoanga/brir.png)
EXT-28
< ON-VEHICLE REPAIR >
ROOF SIDE MOLDING
ROOF SIDE MOLDING
Exploded View
INFOID:0000000000961808
Removal and Installation
INFOID:0000000000961809
REMOVAL
1.
Remove front fender cover (LH/RH). Refer to
EXT-18, "Removal and Installation"
2.
Disengage clips while pinching molding from roof rear end to
front end.
INSTALLATION
Install from roof side molding rear end to front end in this order after temporarily holding.
1.
Roof side molding
2.
Molding fastener (upper)
3.
Molding fastener (lower)
4.
Rivet
5.
Roof side molding clip
6.
Body side panel
7.
Roof panel
Clip
JMKIA0082GB
PIIB2749J
ROOF SIDE MOLDING
EXT-29
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
REMOVAL AND INSTALLATION OF ROOF SIDE MOLDING CLIP
Removal
1.
Remove roof side molding.
2.
Heat adhesive tape interface using a dryer, and then peel roof side molding clips (body side) using long-
nose pliers.
CAUTION:
Be careful not to damage the body.
Installation
1.
Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2.
Use two-part epoxy adhesive.
3.
Apply adhesive evenly to clip tape surface.
4.
Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
5.
Tape clips after press fit, and temporarily hold it for specified time based on the following.
6.
Install from roof side molding rear end to front end in this order after temporarily holding.
CAUTION:
• Use double-faced adhesive tape after hardening for clips.
• Securely insert molding rear end cap onto roof rear end cutout (installation standard).
• When installing roof side molding of windshield portion, check that molding fastener is securely
inserted and then press in.
• Do not wash the vehicle with in 24 hours so as to keep adhesive.
Adhesive
: 3M-weld DP–100 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Press-fit limit
: 19.6 N·
×
2 seconds
×
5 to 10
°
C (41 to 50
°
F)
: 1 hour or more
11 to 23
°
C (52 to 73
°
F)
: 30 minutes or more
24
°
C or more (75
°
F or more)
: 15 minutes or more
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст