Infiniti G35 (V35) Sedan. Manual — part 832
![](/vehicles/zatt/tenge/utoanga/lye.png)
IP-24
< ON-VEHICLE REPAIR >
CENTER CONSOLE ASSEMBLY
• Remove clips from rear of console finisher, and then remove pawl of front. Pull console finisher upward
to disengage from center console.
• Disconnect harness connectors.
5.
Remove screws (B) of center console front side with screw
driver (A).
6.
Remove rear upper console assembly. (AT Models only)
• Slide to front, pull up rear upper console assembly (1), and
disconnect metal clips.
• Disconnect heated seat switch harness connectors. (with
heated seat)
7.
Disconnect auxiliary input jacks connector (A) and power socket
harness connector (B). (AT Models only)
1.
Console finisher (AT models)
2.
Console finisher (MT models)
: Pawl
: Metal clip
JMJIA0031GB
JMJIA0032GB
: Pawl
: Metal clip
JMJIA0033GB
JMJIA0065ZZ
![](/vehicles/zatt/tenge/utoanga/zueshi.png)
CENTER CONSOLE ASSEMBLY
IP-25
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
8.
Disconnect console sub harness connectors (A). (MT Models
only)
9.
Disconnect heated seat switch connector (A). (MT models with
heated seat only)
10. Remove coin pocket fixing pawl using a remover tool (A), and
then remove coin pocket (1). (MT Models only)
11. Insert a deep-well socket wrench (A) to rotate adjusting nut to
loosen cable sufficiently. (MT Models only) Refer to
"LEVER TYPE : Inspection and Adjustment"
.
12. Remove console rear finisher.
• Pull back the console rear finisher (1).
• Disconnect inside key antenna connector (A).
JMJIA0038GB
JMJIA0286ZZ
: Pawl
JMJIA0034GB
JMJIA0035GB
: Metal clip
JMJIA0037GB
![](/vehicles/zatt/tenge/utoanga/zactha.png)
IP-26
< ON-VEHICLE REPAIR >
CENTER CONSOLE ASSEMBLY
13. Remove console mask.
• Open the console lid.
• Pull up console mask (1) by using a remover tool (C), and disengage pawls.
14. Remove screws (C) of center console rear side, and then remove center console assembly (1).
INSTALLATION
Install in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000000960458
DISASSEMBLY AND ASSEMBLY OF CENTER CONSOLE (AT MODELS)
Disassembly
1.
Remove screws of console finisher assembly back side, and remove ashtray (front portion).
2.
Remove rear upper console assembly. Refer to
3.
Remove screws and remove cup holder assembly.
4.
Remove screws and remove console front bracket.
5.
Remove console mask. Refer to
.
6.
Remove console lid mounting screws and remove console lid.
7.
Remove metal clips and remove console rear finisher. Refer to
.
8.
Remove console ashtray.
9.
Remove screw and remove console ashtray bracket.
10. Remove console pocket from center console assembly.
11. Remove auxiliary input jacks and socket knob, cigarette lighter case.
Assembly
(A)
Console mask (with rear ventilator grille)
(B)
Console mask (without rear ventilator grille)
: Pawl
JMJIA0036GB
(A)
Console mounting screws
(with rear ventilator grille)
(B)
Console mounting screws
(without rear ventilator grille)
JMJIA0039GB
CENTER CONSOLE ASSEMBLY
IP-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Assemble in the reverse order of disassembly.
DISASSEMBLY AND ASSEMBLY OF CENTER CONSOLE (MT MODELS)
Disassembly
1.
Remove screws of console finisher assembly back side, and remove ashtray (front portion).
2.
Remove coin pocket. Refer to
3.
Remove console mask. Refer to
.
4.
Remove console lid mounting screws and remove console lid.
5.
Remove metal clips and remove console rear finisher. Refer to
.
6.
Remove console ashtray.
7.
Remove screw and remove console ashtray bracket.
8.
Remove screws and remove cup holder assembly.
9.
Remove auxiliary input jacks and socket knob, cigarette lighter case.
10. Remove console sub harness.
Assembly
Assemble in the reverse order of disassembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст