Infiniti G35 (V35) Sedan. Manual — part 215
![](/vehicles/zatt/tenge/outheneren/bibe.png)
BCS
COMBINATION SWITCH SYSTEM SYMPTOMS
BCS-77
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000000963915
1.
Perform “Data Monitor” of CONSULT-III to check for any malfunctioning item.
2.
Check the malfunction combinations.
Malfunction item:
×
3.
Identify the malfunctioning part from the agreed combination and repair or replace the part.
Malfunction combi-
nation
Data monitor item
FR WI
PER HI
FR WIP
E
R LOW
F
R
W
A
SH
ER
S
W
FR WI
PER INT
INT VOL
U
ME
TURN SIG
N
AL R
TURN SIGNAL L
T
A
IL
LA
MP
SW
H
I BEAM SW
HEAD LAMP SW
1
HEAD LAMP SW
2
P
ASSI
N
G
SW
AU
T
O
LI
GH
T
S
W
FR F
O
G
SW
A
×
×
×
×
B
×
×
×
×
C
×
×
×
D
×
×
×
E
×
×
F
×
×
G
×
×
H
×
×
×
I
×
×
×
×
J
×
×
×
×
K
All Items
L
If only one item is detected or the item is not applicable to the combinations A to K
Malfunction
combination
Malfunctioning part
Repair or replace
A
Combination switch INPUT 1 circuit
Inspect the combination switch input circuit applicable to the malfunctioning
part. Refer to
.
B
Combination switch INPUT 2 circuit
C
Combination switch INPUT 3 circuit
D
Combination switch INPUT 4 circuit
E
Combination switch INPUT 5 circuit
F
Combination switch OUTPUT 1 circuit
Inspect the combination switch output circuit applicable to the malfunction-
ing part. Refer to
.
G
Combination switch OUTPUT 2 circuit
H
Combination switch OUTPUT 3 circuit
I
Combination switch OUTPUT 4 circuit
J
Combination switch OUTPUT 5 circuit
K
BCM
Replace BCM.
L
Combination switch
Replace the combination switch.
BCS-78
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000000963916
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
![](/vehicles/zatt/tenge/outheneren/ramp.png)
BCS
BCM (BODY CONTROL MODULE)
BCS-79
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ON-VEHICLE REPAIR
BCM (BODY CONTROL MODULE)
Exploded View
INFOID:0000000000963917
Removal and Installation
INFOID:0000000000963918
REMOVAL
1.
Remove instrument side finisher (RH). Refer to
IP-12, "Removal and Installation"
2.
Remove dash side finisher (passenger side). Refer to
INT-13, "Removal and Installation"
3.
Remove bolt and nut.
4.
Remove BCM and disconnect the connector.
INSTALLATION
Install in the reverse order of removal.
1.
BCM
JPMIA0063ZZ
![](/vehicles/zatt/tenge/outheneren/datitrearsar.png)
BCS-80
< ON-VEHICLE REPAIR >
COMBINATION SWITCH
COMBINATION SWITCH
Exploded View
INFOID:0000000000963919
Removal and Installation
INFOID:0000000000963920
REMOVAL
1.
Remove steering column cover. Refer to
IP-12, "Removal and Installation"
2.
Remove screws.
3.
Disconnect the connector.
4.
Pull up the combination switch to remove it.
INSTALLATION
Install in the reverse order of removal.
1.
Combination switch
2.
Combination switch connector
JPLIA0050ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст