Infiniti G35 (V35) Sedan. Manual — part 935
![](/vehicles/zatt/tenge/utoanga/xut.png)
DOOR MIRROR
MIR-67
< ON-VEHICLE REPAIR >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DOOR MIRROR
Exploded View
INFOID:0000000000962349
Removal and Installation
INFOID:0000000000962350
REMOVAL
1.
Remove the front door finisher. Refer to
INT-10, "Removal and Installation"
2.
Remove the corner cover.
3.
Disconnect the door mirror harness connector.
4.
Remove the door mirror mounting nuts, and remove the door mirror assembly.
CAUTION:
Do not damage the mirror bodies.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Do not damage the mirror bodies.
1.
Corner cover
2.
Door mirror assembly
Clip
JMLIA0001ZZ
![](/vehicles/zatt/tenge/utoanga/llden.png)
MIR-68
< ON-VEHICLE REPAIR >
[WITH ADP]
DOOR MIRROR REMOTE CONTROL SWITCH
DOOR MIRROR REMOTE CONTROL SWITCH
Exploded View
INFOID:0000000000962351
Removal and Installation
INFOID:0000000000962352
REMOVAL
1.
Remove the power window main switch finisher (2).
Refer to
INT-10, "Removal and Installation"
.
2.
Remove door mirror remote control switch (1) from power win-
dow main switch finisher (2) using screw driver (A).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMLIA0011ZZ
![](/vehicles/zatt/tenge/utoanga/odonde.png)
DOOR MIRROR
MIR-69
< DISASSEMBLY AND ASSEMBLY >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DISASSEMBLY AND ASSEMBLY
DOOR MIRROR
Exploded View
INFOID:0000000000962353
Disassembly
INFOID:0000000000962354
1.
Place the mirror body with mirror glass facing upward.
2.
Put a strip of protective tape B on mirror body.
3.
As shown in the figure, insert a small slotted screwdriver A into
the recess between mirror base (mirror holder)(1) and mirror
holder bracket (2). Push up two pawls (3) to remove mirror
holder lower half side.
NOTE:
When pushing up pawls do not attempt to use one recess only,
be sure to push up with both recesses.
Insert screwdriver into recesses, and push up while rotating
(twisting) to make work easier.
4.
Remove two terminals of mirror heater attachment.
5.
Lightly lift up lower side of mirror surface from mirror surface, and detach two pawls of upper side as if
pulling it out. Remove mirror surface from mirror body.
NOTE:
Be careful not to allow grease on sealing agent in center of mirror body assembly (actuator) or back side
of mirror surface (mirror holder).
6.
Remove the clips and mirror cover from the housing.
Assembly
INFOID:0000000000962355
1.
Install the mirror cover.
2.
Place mirror holder bracket and mirror body assembly (actuator) in a horizontal position.
1.
Mirror (mirror holder)
2.
Mirror assembly
3.
Mirror cover
Pawl
JMLIA0002ZZ
PIIB8320J
![](/vehicles/zatt/tenge/utoanga/zares.png)
MIR-70
< DISASSEMBLY AND ASSEMBLY >
[WITH ADP]
DOOR MIRROR
3.
Connect two terminals of heater installed mirror.
4.
Fit the upper two pawls on the mirror face (1) onto the mirror
holder bracket (2) first, then press the lower side of mirror face
until a click sound is heard to engage the lower pawls.
NOTE:
After installation, visually check that lower two pawls are
securely engaged from the bottom of mirror face.
PIIB3306J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст