Infiniti G35 (V35) Sedan. Manual — part 622
![](/vehicles/zatt/tenge/utoanga/plyb.png)
ENGINE ASSEMBLY
EM-87
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
*: Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.
Other oils and fluid*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gases
—
Leakage
—
![](/vehicles/zatt/tenge/utoanga/caicahed.png)
EM-88
< DISASSEMBLY AND ASSEMBLY >
ENGINE STAND SETTING
DISASSEMBLY AND ASSEMBLY
ENGINE STAND SETTING
Setting
INFOID:0000000000956271
NOTE:
Explained here is how to disassemble with engine stand supporting transmission surface. When using differ-
ent type of engine stand, note with difference in steps and etc.
1.
Remove the engine assembly from the vehicle. Refer to
2.
Remove the parts that may restrict installation of engine to widely use engine stand.
NOTE:
The procedure is described assuming that you use a widely use engine stand holding the surface, to
which transmission is installed.
• Remove clutch cover and clutch disc (M/T models). Refer to
• Remove drive plate (A/T models) or flywheel (M/T models) with power tool. Fix crankshaft with a ring
gear stopper [SST: KV10118600 (J-48641)], and remove mounting bolts.
• Loosen mounting bolts in diagonal order.
• Check for deformation or damage drive plate (A/T models) or flywheel (M/T models).
CAUTION:
• Do not disassemble drive plate (A/T models) or flywheel (M/T models).
• Never place drive plate (A/T models) or flywheel (M/T models) with signal plate facing down.
• When handling signal plate, take care not to damage or scratch it.
• Handle signal plate in a manner that prevents it from becoming magnetized.
3.
Remove pilot converter (A/T models) using the pilot bushing
puller [SST: ST1661001 (J-23907)] (A) as necessary.
4.
Lift the engine with hoist to install it onto the widely use engine stand.
CAUTION:
Use an engine stand that has a load capacity [220 kg (441 lb) or more] large enough for supporting
the engine weight.
• If the load capacity of the stand is not adequate, remove the following parts beforehand to reduce the
potential risk of overturning the stand.
- Remove intake manifold collector. Refer to
- Remove intake manifold. Refer to
- Remove fuel injector and fuel tube assembly. Refer to
.
- Remove ignition coil. Refer to
- Remove rocker cover. Refer to
- Remove exhaust manifold. Refer to
- Other removable brackets.
NOTE:
JPBIA0193ZZ
![](/vehicles/zatt/tenge/utoanga/trks.png)
ENGINE STAND SETTING
EM-89
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
The figure shows an example of widely use engine stand (A)
that can hold mating surface of transmission with drive plate
(A/T models) or flywheel (M/T models) removed.
CAUTION:
Before removing the hanging chains, make sure the
engine stand is stable and there is no risk of overturning.
5.
Drain engine oil. Refer to
.
6.
Drain engine coolant by removing water drain plugs (1) and (4)
from cylinder block both sides as shown in the figure.
JPBIA0190ZZ
2
: Washer
3
: Plug
: Engine front
JPBIA0191ZZ
![](/vehicles/zatt/tenge/utoanga/eje.png)
EM-90
< DISASSEMBLY AND ASSEMBLY >
ENGINE UNIT
ENGINE UNIT
Disassembly
INFOID:0000000000956272
1.
Remove intake manifold collector. Refer to
2.
Remove intake manifold. Refer to
3.
Remove exhaust manifold. Refer to
.
4.
Remove oil pan (lower). Refer to
5.
Remove ignition coil, spark plug and rocker cover. Refer to
6.
Remove fuel injector and fuel tube. Refer to
7.
Remove timing chain. Refer to
.
8.
Remove rear timing chain case. Refer to
.
9.
Remove camshaft. Refer to
10. Remove cylinder head. Refer to
Assembly
INFOID:0000000000956273
Assembly in the reverse order of disassembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст