Infiniti G35 (V35) Sedan. Manual — part 1395
TM-272
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
A/T FLUID COOLER TUBE
5.
Remove the A/T fluid cooler tube from the A/T assembly and engine assembly.
6.
Remove the stabilizer bar. Refer to
.
7.
Loosen the lower mounting nuts for the engine mounting insulators (RH and LH). Refer to
.
8.
Set an engine stand to the engine assembly and slightly lift the engine assembly.
CAUTION:
Do not pull the harnesses, hoses, etc. excessively.
9.
Remove the A/T fluid cooler tube from the vehicle.
CAUTION:
Be careful not to bend A/T fluid cooler tube.
INSTALLATION
Install in the reverse order of removal.
2WD : Inspection
INFOID:0000000000957176
INSPECTION AFTER INSTALLATION
After completing installation, check for A/T fluid leakage and A/T fluid level. Refer to
.
AWD
AWD : Exploded View
INFOID:0000000000957177
![](/vehicles/zatt/tenge/outheneren/mantthy.png)
A/T FLUID COOLER TUBE
TM-273
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AWD : Removal and Installation
INFOID:0000000000957178
REMOVAL
1.
Remove the front and rear engine undercover with power tool.
2.
Remove the front suspension member. Refer to
3.
Remove exhaust front tube and center muffler with power tool. Refer to
.
4.
Remove exhaust mounting bracket. Refer to
5.
Remove the three way catalyst (right bank). Refer to
6.
Remove front propeller shaft. Refer to
.
7.
Pull out the A/T fluid cooler hose from the A/T fluid cooler tube. Refer to
8.
Remove the A/T fluid cooler tube from the A/T assembly and engine assembly.
CAUTION:
1.
Engine assembly
2.
A/T assembly
3.
Copper washer
4.
A/T fluid cooler tube
5.
Bracket
6.
Bracket
Refer to
JPDIA0054GB
TM-274
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
A/T FLUID COOLER TUBE
Be careful not to bend A/T fluid cooler tube.
INSTALLATION
Install in the reverse order of removal.
AWD : Inspection
INFOID:0000000000957179
INSPECTION AFTER INSTALLATION
After completing installation, check for A/T fluid leakage and A/T fluid level. Refer to
.
![](/vehicles/zatt/tenge/outheneren/tyo.png)
TRANSMISSION ASSEMBLY
TM-275
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
2WD
2WD : Exploded View
INFOID:0000000000957180
2WD : Removal and Installation
INFOID:0000000000957181
REMOVAL
CAUTION:
• When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS)
from the A/T assembly.
• Be careful not to damage sensor edge.
1.
Disconnect the battery cable from the negative terminal.
2.
Remove A/T fluid level gauge.
3.
Remove air cleaner case (RH). Refer to
4.
Remove engine under cover with power tool.
5.
Remove exhaust front tube and center muffler with power tool. Refer to
.
1.
A/T fluid level gauge
2.
A/T fluid charging pipe
3.
O-ring
4.
Copper washer
5.
A/T fluid cooler tube
6.
Bracket
7.
Bracket
8.
A/T assembly
A.
For tightening torque, refer to
275, "2WD : Removal and Installa-
tion"
JPDIA0047GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст