Infiniti G35 (V35) Sedan. Manual — part 655
![](/vehicles/zatt/tenge/utoanga/xxthe.png)
EXL-62
< COMPONENT DIAGNOSIS >
[XENON TYPE]
POWER SUPPLY AND GROUND CIRCUIT
1.
CHECK FUSES AND FUSIBLE LINK
Check that the following IPDM E/R fuses or fusible links are not blown.
Is the fuse fusing?
YES
>> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check voltage between IPDM E/R harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK GROUND CIRCUIT
Check continuity between IPDM E/R harness connectors and ground.
Does continuity exist?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
AFS CONTROL UNIT
AFS CONTROL UNIT : Diagnosis Procedure
INFOID:0000000000962467
1.
FUSE INSPECTION
Check that the following fuses are not fusing.
Is the fuse fusing?
YES
>> Repair the applicable circuit. And then replace the fuse.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
Terminal No.
Signal name
Fuses and fusible link No.
1
Battery power supply
C
—
50
51
Terminals
Voltage
(Approx.)
(+)
(
−
)
IPDM E/R
Connector
Terminal
Ground
E4
1
Battery voltage
2
IPDM E/R
Ground
Continuity
Connector
Terminal
E5
12
Existed
E6
41
Signal name
Connection position
Fuse No.
Capacity
Ignition power supply
FUSE BLOCK (J/B)
3
10 A
![](/vehicles/zatt/tenge/utoanga/dowin.png)
POWER SUPPLY AND GROUND CIRCUIT
EXL-63
< COMPONENT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
1.
Turn ignition switch OFF.
2.
Disconnect AFS control unit harness connector.
3.
Check voltage between AFS control unit harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK GROUND CIRCUIT
Check continuity between AFS control unit harness connectors and ground.
Does continuity exist?
YES
>> Repair harness or connector.
NO
>> Power supply and ground circuit are normal.
Terminals
Voltage
(Approx.)
(+)
(
−
)
AFS control unit
Ground
Connector
Terminal
M16
1
Battery voltage
AFS control unit
Ground
Continuity
Connector
Terminal
M16
25
Existed
![](/vehicles/zatt/tenge/utoanga/pald.png)
EXL-64
< COMPONENT DIAGNOSIS >
[XENON TYPE]
EXTERIOR LAMP FUSE
EXTERIOR LAMP FUSE
Description
INFOID:0000000000962468
Fuse list
Diagnosis Procedure
INFOID:0000000000962469
1.
CHECK FUSE
Check that the following fuses are not fusing.
Is the fuse fusing?
YES
>> Repair the applicable circuit. And then replace the fuse.
NO
>> The fuse is normal.
Unit
Location
Fuse No.
Capacity
Headlamp HI (LH)
IPDM E/R
#54
10 A
Headlamp HI (RH)
IPDM E/R
#55
10 A
Headlamp LO (LH)
IPDM E/R
#56
15 A
Headlamp LO (RH)
IPDM E/R
#57
15 A
Front fog lamp
IPDM E/R
#58
15 A
Parking lamp (also used as the front side mark-
er lamp)
IPDM E/R
#52
10 A
• Tail lamp
• Rear side marker lamp
• License plate lamp
• Each illumination
IPDM E/R
#53
10 A
Stop lamp
FUSE BLOCK (J/B)
#7
10 A
Back-up lamp
FUSE BLOCK (J/B)
#4
10 A
Unit
Location
Fuse No.
Capacity
Headlamp HI (LH)
IPDM E/R
#54
10 A
Headlamp HI (RH)
IPDM E/R
#55
10 A
Headlamp LO (LH)
IPDM E/R
#56
15 A
Headlamp LO (RH)
IPDM E/R
#57
15 A
Front fog lamp
IPDM E/R
#58
15 A
Parking lamp (also used as
the front side marker lamp)
IPDM E/R
#52
10 A
• Tail lamp
• Rear side marker lamp
• License plate lamp
• Each illumination
IPDM E/R
#53
10 A
Stop lamp
FUSE BLOCK (J/
B)
#7
10 A
Back-up lamp
FUSE BLOCK (J/
B)
#4
10 A
![](/vehicles/zatt/tenge/utoanga/glig.png)
HEADLAMP (HI) CIRCUIT
EXL-65
< COMPONENT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HEADLAMP (HI) CIRCUIT
Description
INFOID:0000000000962470
The high beam solenoid drives the mobile valve shade. And the mobile valve shade switches the high beam
and low beam of headlamp.
• When the head lamp high relay is turned ON, magnetic force is
applied to the high beam solenoid (1) by a current. The mobile
valve shade (3) is switched to the high beam position through the
actuator rod (2).
• When the head lamp high relay is turned OFF, the current stops.
The mobile valve shade returns to the low beam position automati-
cally.
Component Function Check
INFOID:0000000000962471
1.
CHECK HEADLAMP (HI) OPERATION
IPDM E/R AUTO ACTIVE TEST
1.
Start IPDM E/R auto active test. Refer to
PCS-10, "Diagnosis Description"
2.
Check that the headlamp switches to the high beam.
CONSULT-III ACTIVE TEST
1.
Select "EXTERNAL LAMP" of IPDM E/R active test item.
2.
With operating the test items, check that the headlamp switches to the high beam.
NOTE:
HI/LO is repeated 1 second each when using the IPDM E/R auto active test.
Does the headlamp switch to the high beam?
YES
>> Headlamp (HI) circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000000962472
1.
CHECK HEADLAMP (HI) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1.
Turn the ignition switch OFF.
2.
Disconnect the front combination lamp connector.
3.
Turn the ignition switch ON.
4.
Select "EXTERNAL LAMP" of IPDM E/R active test item.
5.
With operating the test items, check the voltage between the IPDM E/R harness connector and the
ground.
JSLIA0003ZZ
HI
: Headlamp switches to the high beam.
OFF
: Headlamp OFF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст