Infiniti EX35. Manual — part 1462
![](/vehicles/zatt/rylld/ivere/bossaknda.png)
TM-236
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
iv.
Install bearing race to output shaft.
v.
Install gasket onto transmission case.
CAUTION:
• Completely remove all moisture, oil and old gasket, etc.
from the transmission case and adapter case assembly
mounting surfaces.
• Do not reuse gasket.
vi. Install adapter case assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the adapter
case assembly.
vii. Tighten adapter case assembly bolts (1) to the specified torque.
[With bracket (2).]
SCIA5245E
SCIA5231E
SCIA5186E
3
: Self-sealing bolt
: Bolt
SCIA6910E
![](/vehicles/zatt/rylld/ivere/inoy.png)
TRANSMISSION ASSEMBLY
TM-237
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
31. Install needle bearing in drum support.
CAUTION:
Check the direction of needle bearing. Refer to
"Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
32. Install direct clutch assembly in reverse brake.
CAUTION:
Make sure that drum support edge surface and direct clutch
inner boss edge surface come to almost same place.
33. Install high and low reverse clutch assembly in direct clutch.
34. Using a flat-bladed screwdriver, align the drive plate.
35. Install high and low reverse clutch hub, mid sun gear assembly
and rear sun gear assembly as a unit.
SCIA5198E
SCIA5019E
SCIA2306E
SCIA3169E
SCIA5018E
![](/vehicles/zatt/rylld/ivere/zietr.png)
TM-238
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
CAUTION:
Make sure that portion “A” of high and low reverse clutch
drum protrudes approximately 2 mm (0.08 in) beyond por-
tion “B” of rear sun gear.
36. Install needle bearing in rear carrier assembly.
CAUTION:
Check the direction of needle bearing. Refer to
"Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
37. Install bearing race in rear carrier assembly.
CAUTION:
Check the direction of needle bearing. Refer to
"Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
38. Install rear carrier assembly in direct clutch drum.
SCIA3130E
SCIA2803E
SCIA5175E
SCIA2462E
![](/vehicles/zatt/rylld/ivere/qunk.png)
TRANSMISSION ASSEMBLY
TM-239
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
39. Install needle bearing (rear side) to mid carrier assembly.
CAUTION:
Check the direction of needle bearing. Refer to
"Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
40. Install needle bearing (front side) to mid carrier assembly.
CAUTION:
Check the direction of needle bearing. Refer to
"Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
41. Install mid carrier assembly in rear carrier assembly.
42. Install front carrier assembly, input clutch assembly and rear
internal gear as a unit.
43. Install seal rings in input clutch assembly.
SCIA2804E
SCIA2805E
SCIA5017E
SCIA5015E
SCIA2470E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст