Infiniti EX35. Manual — part 1342
CRASH ZONE SENSOR
SR-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• In the case that a malfunction is detected by the air bag warning lamp, after reparation or replace-
ment of the malfunctioning parts, reset the memory by self-diagnosis or by the CONSULT-III.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to
![](/vehicles/zatt/rylld/azoru/bent.png)
SR-14
< ON-VEHICLE REPAIR >
SIDE AIR BAG (SATELLITE) SENSOR
SIDE AIR BAG (SATELLITE) SENSOR
Exploded View
INFOID:0000000003131592
Removal and Installation
INFOID:0000000003131593
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes.
• Do not use air tools or electric tools for servicing.
REMOVAL
1.
Remove the front seat belt. Refer to
SB-5, "SEAT BELT RETRACTOR : Removal and Installation"
2.
Remove the side air bag (satellite) sensor fixing nuts.
3.
Disconnect harness connector and then remove side air bag (satellite) sensor.
CAUTION:
• Replace the satellite sensor if it has been dropped or sus-
tained an impact.
• Replace the satellite sensor of deployed SRS front side air
bag module and deployed SRS side curtain air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Do not use old fixing nuts after removal; replace with new nuts.
1.
Side air bag (satellite) sensor
A.
Side air bag (satellite) sensor har-
ness connector
: Vehicle front
Refer to
for symbols in the figure
JMHIA0549GB
JMHIA0009ZZ
SIDE AIR BAG (SATELLITE) SENSOR
SR-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• In the case that a malfunction is detected by the air bag warning lamp, after reparation or replace-
ment of the malfunctioning parts, reset the memory by self-diagnosis or by the CONSULT-III.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to
![](/vehicles/zatt/rylld/azoru/ree.png)
SR-16
< ON-VEHICLE REPAIR >
DIAGNOSIS SENSOR UNIT
DIAGNOSIS SENSOR UNIT
Exploded View
INFOID:0000000003131594
Removal and Installation
INFOID:0000000003131595
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
• Before disconnecting the air bag diagnosis sensor unit harness connectors, be sure to disconnect
the each harness connector of the air bag module and seat belt pre-tensioner to prevent air bag
deployment by static electricity and seat belt pre-tensioner operation.
• Do not use air tools or electric tools for servicing.
REMOVAL
1.
Disconnect each connector of all air bag modules and pre-tensioner seat belts.
2.
Remove the center console assembly. Refer to
IP-22, "Removal and Installation"
3.
Disconnect diagnosis sensor unit harness connector.
4.
Remove the fixing bolts, ground bolt, and then remove diagnosis sensor unit.
CAUTION:
• Replace the air bag diagnosis sensor unit if it has been
dropped or sustained an impact.
• Replace the air bag diagnosis sensor unit of deployed SRS air
bag and deployed front seat belt pre-tensioner.
INSTALLATION
Install in the reverse order of removal.
1.
Diagnosis sensor unit
A.
Diagnosis sensor unit harness connector
B.
Ground bolt
Refer to
for symbols in the figure
JMHIA0550GB
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст