Infiniti EX35. Manual — part 17
![](/vehicles/zatt/rylld/azoru/cthe.png)
ADP-62
< COMPONENT DIAGNOSIS >
SLIDING SWITCH
SLIDING SWITCH
Description
INFOID:0000000003134677
Sliding switch is equipped to the power seat switch on the seat cushion side surface. The operation signal is
inputted to the driver seat control unit when the sliding switch is operated.
Component Function Check
INFOID:0000000003134678
1.
CHECK FUNCTION
1.
Turn ignition switch ON.
2.
Select “SLIDE SW-FR”, “SLIDE SW-RR” in “Data monitor” mode with CONSULT-III.
3.
Check sliding switch signal under the following conditions.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000003134679
1.
CHECK SLIDING SWITCH SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between power seat switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SLIDING SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit connector.
3.
Check continuity between driver seat control unit harness connector and power seat switch harness con-
nector.
4.
Check continuity between driver seat control unit harness connector and ground.
Monitor item
Condition
Status
SLIDE SW-FR
Sliding switch (forward)
Operate
ON
Release
OFF
SLIDE SW-RR
Sliding switch (backward)
Operate
ON
Release
OFF
(+)
(–)
Voltage (V)
(Approx.)
Power seat switch
Connector
Terminal
B459
11
Ground
Battery voltage
26
Driver seat control unit
Power seat switch
Continuity
Connector
Terminal
Connector
Terminal
B451
11
B459
11
Existed
26
26
![](/vehicles/zatt/rylld/azoru/ssstrooug.png)
SLIDING SWITCH
ADP-63
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
ADP-209, "Removal and Installation"
NO
>> Repair or replace harness or connector.
3.
CHECK SLIDING SWITCH
ADP-63, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace power seat switch. Refer to
ADP-212, "Removal and Installation"
.
4.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003134680
1.
CHECK SLIDING SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch connector.
3.
Check continuity between power seat switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace power seat switch. Refer to
ADP-212, "Removal and Installation"
.
Driver seat control unit
Ground
Continuity
Connector
Terminal
B451
11
Not existed
26
Power seat switch
Condition
Continuity
Terminal
32
11
Sliding switch (backward)
Operate
Existed
Release
Not existed
26
Sliding switch (forward)
Operate
Existed
Release
Not existed
![](/vehicles/zatt/rylld/azoru/czesclat.png)
ADP-64
< COMPONENT DIAGNOSIS >
RECLINING SWITCH
RECLINING SWITCH
Description
INFOID:0000000003134681
Reclining switch is equipped to the power seat switch on the seat cushion side surface. The operation signal is
inputted to the driver seat control unit when the reclining switch is operated.
Component Function Check
INFOID:0000000003134682
1.
CHECK FUNCTION
1.
Turn ignition switch ON.
2.
Select “RECLN SW-FR”, “RECLN SW-RR” in “Data monitor” mode with CONSULT-III.
3.
Check reclining switch signal under the following conditions.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000003134683
1.
CHECK RECLINING SWITCH SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between power seat switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK RECLINING SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit connector.
3.
Check continuity between driver seat control unit harness connector and power seat switch harness con-
nector.
4.
Check continuity between driver seat control unit harness connector and ground.
Monitor item
Condition
Status
RECLINE SW-FR
Reclining switch (forward)
Operate
ON
Release
OFF
RECLINE SW-RR
Reclining switch (backward)
Operate
ON
Release
OFF
(+)
(–)
Voltage (V)
(Approx.)
Power seat switch
Connector
Terminal
B459
12
Ground
Battery voltage
27
Driver seat control unit
Power seat switch
Continuity
Connector
Terminal
Connector
Terminal
B451
12
B459
12
Existed
27
27
![](/vehicles/zatt/rylld/azoru/ntiloth.png)
RECLINING SWITCH
ADP-65
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
ADP-209, "Removal and Installation"
NO
>> Repair or replace harness or connector.
3.
CHECK RECLINING SWITCH
ADP-65, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace power seat switch. Refer to
ADP-212, "Removal and Installation"
.
4.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003134684
1.
CHECK RECLINING SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch connector.
3.
Check continuity between power seat switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace power seat switch. Refer to
ADP-212, "Removal and Installation"
Driver seat control unit
Ground
Continuity
Connector
Terminal
B451
12
Not existed
27
Power seat switch
Condition
Continuity
Terminal
32
12
Reclining switch (backward)
Operate
Existed
Release
Not existed
27
Reclining switch (forward)
Operate
Existed
Release
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст